Предлагаемое устройство предназначаетс дл наполнени землей опоки в формовочной машине с верхним прессованиеи таким образом , что поверх старой земли насыпаетс слой свежей.The proposed device is intended to fill the soil of the flask in a molding machine with top pressing in such a way that a layer of fresh is poured over the old earth.
На чертеже фиг. 1 и 2 изображают поперечный разрез устройства при двух положени х каретки; фиг. 3-вид спереди; фиг. 4 - вид сверху.In FIG. 1 and 2 show a cross section of the device at two positions of the carriage; FIG. 3 is a front view; FIG. 4 - top view.
Опока 1 стоит па подкладной плите 2 пресса и находитс под его наполнительным щиком 3. Формовочна земл насыпаетс в опоку и щик, и прессуетс опусканиен модельной плиты 4 с моделью 5. Занас наполнительной (старой) земли находитс в бункере б, запас модельной (свежей) земли - в бункере 7. Под бункерами находитс каретка 8, опирающа с роликами 9 на рельсы 10. Каретке может быть сообщено возвратно-поступательное движение шатуном 11 от механизма любой конструкции. В исходном , крайнем правом положении каретки (фиг. 1) ее отсек 12 стоит под бункером 6 и заполн етс из него старой землей; а отсек 13 стрит под бункером 7 и наполн етс свежей землей, так как задвижка 14 открыта, будучи отт нута кареткой 8, нажимающей наFlask 1 stands on the base plate 2 of the press and is located under its filling box 3. The molding earth is poured into the flask and the box, and the lowering of the model plate 4 with model 5 is pressed. Zanas filling (old) earth is in the bunker b, the stock of model (fresh) land in the bunker 7. Under the bunkers there is a carriage 8, supporting rollers 9 on the rails 10. The carriage can be informed by the reciprocating movement of the connecting rod 11 from the mechanism of any design. In the initial, rightmost position of the carriage (Fig. 1), its compartment 12 stands under the hopper 6 and is filled out of it with old earth; and the 13 Street compartment under the bunker 7 and is filled with fresh ground, since the valve 14 is open, being pulled away by the carriage 8, pressing on
бородку 16 т ги 15. Получив движение влево, каретка волочит старую землю по плите 17 к наполнительному щику 3, ссыпает ее в щик и разравпивает ее продвижением кромки 18 отсека 6 почти до кромки 19 щика 3. В это врем свежа земл не высыпаетс , так как она заперта нижней задвижкой 20, прижатой к стенке отсека давлением пружины 21 через т гу 22. При обратной движении (внраво), каретка 8 обратно снова приглаживает насыпанную в щик 3 старую землю кромкой 23 отсека 12. Когда отсек 13 дойдет (при движении вправо) до кромки 19 щика 3, открываетс задвижка 20 и свежал земл начинает насыпатьс поверх CTapoit в виде сло , то.щина которого зависит от высоты расположени задвижки 20 (фиг. 2). Когда же кромка 23 отсека 12 дойдет до правой кромки щика 3, задвижка 20 снов закрываетс , при чем слой свежей земли увв покрыл старую землю. Вернувшись в свес исходное (правое) положение, каретка 8, ио достижении кромкой 24 конца задвижки 14, нажимает на бородку 16 и открывает эту задвижку, раст гива пружину 25. Таким образом, все врем , отсек 12 защищен от попадани в него свежей „модельной зеили.16-giggle beard 15. Having received a movement to the left, the carriage drags the old earth along plate 17 to the filling box 3, pours it into the box and spreads it by advancing the edges 18 of the compartment 6 almost to the edge 19 of box 3. At this time, fresh earth does not pour out, so as it is locked by the lower valve 20, pressed against the wall of the compartment by the pressure of the spring 21 through tgu 22. When reversing (inside), the carriage 8 again smoothes the old earth poured into box 3 with the old edge 23 of compartment 12. When compartment 13 comes (moving to the right ) to the edge 19 of the box 3, the valve 20 is opened and the al excavation begins nasypats CTapoit over a layer to.schina which depends on the height positioning of the valve 20 (FIG. 2). When the edge 23 of the compartment 12 reaches the right edge of the crate 3, the dream valve 20 is closed, and a layer of fresh ground UHV covers the old ground. Returning to the overhang of the initial (right) position, the carriage 8, and when the edge 24 reaches the end of the valve 14, presses the beard 16 and opens this valve, stretching the spring 25. Thus, all the time, the compartment 12 is protected from being hit by a fresh “model” zeili.