Gebrauchsmuster-Anmeldung
71-.. !.''/
Krawattenklammer""-'"""''J'""/"
Die Verwendung von Fertigkrawatten mit Druckknopfbefestigung
ist
daran gebunden, dass der Hemdkragen eine Durchstecköffnung'besitzt,
welche die Einführung eines druckknopfartigen Verschlussteils
er-
möglichst, so dass die Krawatte einrasten kann. Sporthemden
mit
festen Kragen liessen bisher eine Verwendung solcher Krawatten
nicht zu.
Zur Behebung dieses Nachteils ist nun erfindungsgemäss eine
Klammer
IZD
geschaffen worden welche aus einer Druckknopfkugel besteht
an
welche ein aus Draht, Blech oder Kunststoff gefertigter Bügel
durch
Nietung, Schweissung oder sonstige Befestigung angebracht ist.
Dieser Bügel besitzt eine solche Form., dass er le.'cht von
oben
U. über den Kragen geschoben werden kann und durch Klemm.'irkung
einen
durch Klemn*i"irktin (. r einen
festen Sitz erhält. Die Lage der Druckknopfkugel entspricht
dabei
der Lage des Kragenknopfes.
cl b
Der gleiche Bügel kann auch unmittelbar an den Pappmondchen
der
Fertigkraatten angebracht werden und ermöglicht so in gleicher
x, eise das unmittelbare Einhängen der damit ausgestatteten
Fertig-
CD
krawatten an Hemden mit festem Kragen.
In der beigefügten Zeichnung sind dargestellt :
1. Die Kombination einer Krawattenklammer mit einer
Druckknopfkugel in Vorderansicht und Draufsicht.
2. Die Kombination einer Krawattenllammer mit einem
Möndchen in Vorderansicht und Draufsicht.
<// 1,//
Cchutzanspruch'' -''
Krawattenklammer aus Metall oder Kunststoff zur Befestigung
von
Fertigkrawatten an Hemden mit festem Kragen, dadurch cekennnzeichnet,
dasG der u-förmig gebogene Bügel an seinem k r eren, nde eine
Druc knopfkugel aufweist.
Krawattenklammer wie vor, dadurch gekennzeichnete dass der
Bügel
mit dem Knopf durch Nietung, Pressung oder S h eissung verbunden
ist.
Krawattenklammer'ie vor dadurch gekennzeichnete dass der Bügel
an seinem kurzen Ende unmittelbar an dem Monthen aus Pappe
oder
Kunststoff angebracht ist.
ZD
Krawattenklammer wie vor, dadurch gekennzeichnete dass Bügel
und
Knopf bzw. Bügel und Halbmond einstüclig sind.
Utility model registration
71- ..!. '' /
Tie clip "" - '"""''J'""/"
The use of ready-made ties with snap fasteners is
tied to the fact that the shirt collar has a push-through opening,
which enables the introduction of a snap-fastener-like closure part
if possible, so that the tie can click into place. Sports shirts with
Fixed collars have hitherto allowed such ties to be used
not to.
According to the invention, a clamp is now used to remedy this disadvantage
IZD
which consists of a push button ball
which a bracket made of wire, sheet metal or plastic through
Riveting, welding or other fastening is attached.
This bracket has such a shape that it can be seen from above
U. can be pushed over the collar and a
through Klemn * i "irktin (. r a
gets a firm seat. The position of the push button ball corresponds to this
the position of the collar button.
cl b
The same bracket can also be attached directly to the cardboard moon
Finished kraatten are attached and allows so in the same
x, also the immediate hanging of the ready-made
CD
ties on shirts with a fixed collar.
The attached drawing shows:
1. The combination of a tie clip with one
Push-button ball in front view and top view.
2. The combination of a tie clip with one
Moon in front and top view.
<// 1, //
Protection claim '' - ''
Tie clips of metal or plastic for fastening
Ready-to-wear ties on shirts with a fixed collar, thereby marking
The U-shaped bent bracket at its lower end has one
Has push button ball.
Tie clip as before, characterized in that the bracket
is connected to the button by riveting, pressing or welding.
Tie clips are characterized by the fact that the hanger
at its short end directly to the cardboard mount or
Plastic is attached.
ZD
Tie clip as before, characterized in that bracket and
The button or bracket and crescent are in one piece.