Schnerohr für KohIensäure-FeuerlSsehar
Die Neuerung betrift Schneerohre für Xohlenaäuro-Peuerlöncher
mit tla-
chem Mundstück. Derartige Schneerohre sind bekamt und zwar
sind bei
diesen bekannten Ausführungen die flachen Kundgttelre aug pe
g
Zum Schutze gegen Einwirkung von Feuchtigkeit sind diwe Papprohr
mit
einer Lackschicht überzogen. Es hat sich jedoch immer wieder
geral,
daß diese Lackschicht keinen ausreichenden Schutz bietet und
leicht
beschädigt werden kann, so daß Feuchtigkeit in die Pappe dringt, die Pappe quillt
und so das Schneerohr unbrauchbar wird. Schnerohr for carbonic acid fire oil
The innovation concerns snow pipes for Xohlenaäuro-Peuerlöncher with tla-
chem mouthpiece. Such snow pipes are received and are at
These well-known designs include the flat Kundgttelre aug pe g
To protect against the effects of moisture, there are also cardboard tubes
coated with a layer of lacquer. However, it has always been
that this layer of lacquer does not provide adequate protection and is easy
can be damaged, so that moisture penetrates the cardboard, the cardboard swells and so the snow pipe is unusable.
Weiter sind flexible Schneerohre bekannte Diese bestehen aus zwei,
aus Gummi hergestellten Schalen. wobei die Schalen am Xand
zusammen-
geklebt sind. Derartige Schneerohre sind schwer. Außerdem kommt hinzu, daß die Klebverbindung
nicht ausreichend ist. Der neuerungsgemäße Vorschlag sicht ein Schneerohr mit flachem
Mundstück vor, du werk-
mal darin besteht, daß zwei aus glasfaserverstärktem Yolytoterharn
hergestellte, mit Nut und Feder veraekene Halbaohalen, die
8iteinaa4er
verklebt und an den Enden durch Ringe aus Polyesterharz verstärkt
wind,
verwendet werden. Des weiteren kann die Innenfläche mit einem
DraM
gewebe, Graphitstab oder einem anderen, elektrisch leitendem
Material
ausgekleidet sein, wie auch ein Polyesterharz verwandet werden
kmnn,
das durch Zusatz von Graphit elektrisch leitend gemacht ist. Auf diese Weise wird
die beim Ausströmen der Kohlensäure entstehende Btatioeh « Elektrizität abgeleitet
werden.Flexible snow pipes are also known.These consist of two, trays made of rubber. where the shells at the Xand
are glued. Such snow pipes are heavy. In addition, the adhesive bond is not sufficient. The proposal according to the innovation envisages a snow pipe with a flat mouthpiece, you times is that two are made of fiberglass-reinforced yolytoteric urine
manufactured, with tongue and groove veraekene Halbaohalen, the 8iteinaa4er
glued and reinforced at the ends by rings made of polyester resin,
be used. Furthermore, the inner surface can with a DraM
fabric, graphite rod or another electrically conductive material
be lined, like a polyester resin are used,
which is made electrically conductive by adding graphite. In this way the electricity produced when the carbonic acid flows out will be diverted.
Dieses Material hat eine sehr hohe mechanische Festigkeit, ist nicht
hygroskopisch und weist auch bei Temperaturen unterhalb -20°C noch eine sehr hohe
Festigkeit auf. Ebenfalls ist dieses Material flammenwidrig herzustellen.This material has very high mechanical strength, is not
hygroscopic and has a very high level even at temperatures below -20 ° C
Firmness on. This material must also be made flame-retardant.
Ein Ausführungsbeispiel ist in der Zeichnung beispielsweise dargestellt
und besteht aus den beiden Schalen 1, die an ihrem Rand mit Nut 3 bzw.An exemplary embodiment is shown in the drawing, for example
and consists of the two shells 1, which have a groove 3 or
Feder 2 versehen sind.
Zy, ei Schalen 1 werden mit Nut 3 und Feder 4 zusammengeklebt#
wo da#
sich ein nach vorn verjüngendes Schneerohr mit schmaler Austrittzöffnung ergibt.
Vorn und hinten kann das Schneerohr zur Unterstützung der Klebverbindung mit Verstärkungsringen
4,5 versehen sein. Ein weitmaschiges Drahtgewebe 6 ist in die Schalen 1 beispielsw@ise
eingelegt.Spring 2 are provided. Zy, ei shells 1 are glued together with groove 3 and tongue 4 # where there #
there is a forward tapering snow pipe with a narrow outlet opening. The snow pipe can be provided with reinforcement rings 4, 5 at the front and back to support the adhesive connection. A wide-meshed wire mesh 6 is inserted into the shells 1, for example.