<Desc/Clms Page number 1>
EMI1.1
EMI1.2
EMI1.3
<Desc/Clms Page number 2>
Das unter der Ablenkplatte eintretende Gas trifft auf die Unterseite derselben ; der Gasstrom wird dabei zufolge der Gestalt der Platte verbreitert, hierauf nach abwärts und wieder um Geringes nach aufwärts abgelenkt ; erst nach Zurücklegung dieses Weges kann das Gas zwischen der Ablenkplatte und dem zylindrischen Fortsatz 10 des Gehäuses in abwärts gerichteter Strömungsrichtung in die eigentliche Kammer'5 austreten und nach aufwärts gegen die Membran strömen.
Durch diese oftmalige Richtungsänderung verliert das Gas seine Strömungsenergie und kann nicht mehr durch Stosswirkung auf die Membran zur Wirkung gelangen und dadurch den Druck-
EMI2.1
entsteht, d. h. ein Druck, welcher grösser ist als der Normaldruck, für welchen die Vorrichtung konstruiert ist, so wird derselbe das Ventil 12 auf seinen Sitz 9 pressen. Der Überdruck öffnet jedoch hiebei das Hilfsventil15. wodurch ein Druckausgleich ermöglicht wird, worauf nach Wiedererreichung des Normaldruckes in der Zuleitung die Feder 16 das Hilfsventil 15 auf das Ventil 12 presst und letzteres von seinem Sitze 9 abhebt (siehe Fig. 4 und 5).
Die Stange 19, die oben die Fortsetzung der Stange 11 bildet, kann aus einem Stück mit
EMI2.2
Anzeigevorrichtung b beliebiger Ausführung. z. B. einen drehbar gelagerten Arm, welcher ein Gewicht trägt.
Die Wirkungsweise der Vorrichtung ist folgende : Wenn die Gasentnahme unterbrochen ist, also kein Ausströmen von Gas durch das Entnahmerohr 8 stattfinden kann, so steigt der Druck
EMI2.3
bestimmt ist. Wenn in der Zuleitung ein höherer Druck auftritt, als jener, für welchen der Apparat
EMI2.4
Gasflammen erlöschen, wenn nicht das Hilfsventil lii vorgesehen wäre, welches die Gaszufuhr zu den Verbrauchsstellen unter allen Umständen sichert. Dieses Hilfsventil ist durch eine Feder 16
EMI2.5
im Hauptventil (12) gedrückt wird. derart. dass es erst bei geschlossenem Hauptventil (12) durch Gasüberdmck zur Wirkung gelangt.
<Desc / Clms Page number 1>
EMI1.1
EMI1.2
EMI1.3
<Desc / Clms Page number 2>
The gas entering under the baffle hits the underside of the same; the gas flow is widened according to the shape of the plate, then deflected downwards and again slightly upwards; only after this path has been covered can the gas escape between the baffle plate and the cylindrical extension 10 of the housing in a downward flow direction into the actual chamber 5 and flow upward against the membrane.
As a result of this frequent change of direction, the gas loses its flow energy and can no longer have an impact through impact on the membrane, thereby reducing the pressure
EMI2.1
arises, d. H. a pressure which is greater than the normal pressure for which the device is designed, it will press the valve 12 onto its seat 9. However, the overpressure opens the auxiliary valve 15. whereby a pressure equalization is made possible, whereupon after normal pressure has been reached in the supply line, the spring 16 presses the auxiliary valve 15 onto the valve 12 and the latter lifts off its seat 9 (see FIGS. 4 and 5).
The rod 19, which forms the continuation of the rod 11 at the top, can be made in one piece with
EMI2.2
Display device b of any design. z. B. a rotatably mounted arm which carries a weight.
The mode of operation of the device is as follows: If the gas extraction is interrupted, that is to say no gas can flow out through the extraction pipe 8, the pressure rises
EMI2.3
is determined. If a higher pressure occurs in the supply line than that for which the apparatus
EMI2.4
Gas flames go out if the auxiliary valve lii were not provided, which ensures the gas supply to the consumption points under all circumstances. This auxiliary valve is supported by a spring 16
EMI2.5
is pressed in the main valve (12). like that. that it only takes effect through gas pressure when the main valve (12) is closed.