<Desc/Clms Page number 1>
EMI1.1
EMI1.2
EMI1.3
<Desc/Clms Page number 2>
EMI2.1
drückt. Nun findet ein Zufluss von Speisewasser zum Kessel nicht statt.
Wenn der Wasserstand im Kessel sinkt, wird das Ventil r von seinem Sitze gehoben, so dass die Saugwirkung im Rohr f auf den Zylinder b und auch zum Teil auf die Öffnung h übertragen wird. Infolgedessen wird eine gewisse Saugwirkung auf den Kolben q übertragen, so dass der Schwinghebel M um einen gewissen Winkel nach unten gedreht wird, bis nämlich die Saugwirkung im Zylinder b und die Spannung der Feder e einander das Gleichgewicht halten Hiedurch wird das Ventil a von seinem Sitz gehoben, so dass eine gewisse Speisewassermenge durch das Rohr l dem Kessel zuströmt. Wenn der Wasserstand im Kessel weiter sinkt, so schliesst das Ventil r die Öffnung h allmählich ab, so dass das Ventil a infolge der verstärkten Saugwirkung vollständig abgehoben wird.
Wenn die Öffnung h vollständig geschlossen ist, so ist das Ventil a vollkommen offen, so dass ein starker Zufluss von Speisewasser stattfindet.
In dem in Fig. 2 dargestellten Ausführungsbeispiele dient zum Antrieb des Motors Luft oder ein andere Gas unter Druck. Die Wirkungsweise des Speisewasserventils o. des Motors b und des Schwimmers c entspricht im wesentlichen derjenigen des Ausführungsbeispieles nach Fig. 1. Die Feder e'ist jedoch am Schwinghebel n an der gegenüberliegenden Seite des Drehungspunktes des letzteren angeordnet, und der Kolben (l'befindet sich im allgemeinen am Boden des Zylinders b. Das Rohr f'steht mit einer Zuleitung für Luft oder Gas unter Druck in Verbindung.
Im Betriebe der Einrichtung befindet sich das Ventil r im allgemeinen auf seinem unteren
EMI2.2
sich das Ventil r, so dass Druckluft dem Motor b zuströmt. Hiedurch wird der Kolben entgegen der Spannung der Feder e nach oben gedrückt. Das Ventil a hebt sich von seinem Sitze ab und das Speisewasser strömt dem Kessel zu. Wenn der Wasserstand noch weiter fällt, so schliesst das Ventil r die Öffnung h, so dass die volle Spannung der Druckluft auf den Zylinder b übertragen wird, und das Ventil a vollkommen abgehoben wird.
In dem in Fig. 3 dargestellten Ausführungsbeispiele findet eine Flüssigkeit zum Antrieb des Motors b Verwendung. Die Bauart der Vorrichtung ist nicht wesentlich geändert. nur besitzt die Öffnung 11 ein Ablassrohr y für die verbrauchte Flüssigkeit. Die Wirkungsweise der Einrichtung hat sich gleichfalls nicht geändert. Sie ergibt sich ohneweiters aus der Zeichnung.
PATENT ANSPRÜCHE :
<Desc / Clms Page number 1>
EMI1.1
EMI1.2
EMI1.3
<Desc / Clms Page number 2>
EMI2.1
presses. Now there is no inflow of feed water to the boiler.
When the water level in the boiler drops, the valve r is lifted from its seat, so that the suction in the pipe f is transmitted to the cylinder b and also partly to the opening h. As a result, a certain suction effect is transmitted to the piston q, so that the rocker arm M is rotated downwards through a certain angle, until the suction effect in the cylinder b and the tension of the spring e balance each other.This causes the valve a to move out of its seat raised so that a certain amount of feed water flows through the pipe l to the boiler. If the water level in the boiler continues to fall, the valve r gradually closes the opening h so that the valve a is completely lifted off as a result of the increased suction effect.
When the opening h is completely closed, the valve a is completely open so that a strong inflow of feed water takes place.
In the exemplary embodiment shown in FIG. 2, air or another gas under pressure is used to drive the motor. The mode of operation of the feed water valve o. The motor b and the float c corresponds essentially to that of the exemplary embodiment according to FIG. 1. The spring e 'is, however, arranged on the rocking lever n on the opposite side of the pivot point of the latter, and the piston (l' is located is generally at the bottom of the cylinder b. The tube f 'is connected to a supply line for air or gas under pressure.
In operation of the device, the valve r is generally on its lower
EMI2.2
the valve r, so that compressed air flows to the motor b. This pushes the piston upwards against the tension of the spring e. The valve a lifts off its seat and the feed water flows to the boiler. If the water level falls further, the valve r closes the opening h, so that the full tension of the compressed air is transferred to the cylinder b, and the valve a is completely lifted.
In the exemplary embodiment shown in FIG. 3, a liquid is used to drive the motor b. The design of the device is not significantly changed. only the opening 11 has a drain pipe y for the used liquid. The way the facility works has not changed either. It is evident from the drawing anyway.
PATENT CLAIMS: