Предлагаемый механизм часового бо отличаетс , по мнению изобретател , простотой конструкции и равномерностью бо и может быть применен к обыкновенному ходовому механизму часов-ходиков и других стенных часов.According to the inventor, the proposed mechanism for clock bo is simple in design and uniform bo and can be applied to the ordinary movement of clocks and other wall clocks.
На схематическом чертеже фиг. 1 изображает вид механизма часового бо сбоку; фиг. 2-то же в продольном разрезе.In the schematic drawing of FIG. 1 shows a view of the mechanism of the clock bo from the side; FIG. 2 is the same in longitudinal section.
Все части предлагаемого механизма часового бо укреплены на пластине 7. Минутное колесо 2 снабжено тринадцатью зубцам а передаточное 9 - двенадцатью или двенадцати, так что за первый оборот минутного колеса передаточное делает оборота, за второй оборот- 22/12 оборота и т. д., т.е. за каждый последующий оборот минутного колеса передаточное колесо делает на /i2 оборота больпхе, что должно соответствовать количеству поднимаемых зубцов гребн 6, увеличивающемус с каждым оборотом {от первого до двенадцатого) минутного колеса, соответственно числу ударов;молоточка 7/. Подъем гребн о происходит благодар тому, что расположенный; на передаточном колесе 9 штифт JO нажимает на штифт 8, влекущий за собой гребень 6. Зубец 3, которым снабженаAll parts of the proposed watch mechanism are fixed on the plate 7. The minute wheel 2 is equipped with thirteen teeth and the gear 9 is twelve or twelve, so for the first revolution of the minute wheel the gear makes turns, for the second turn 22/12 turns, etc. those. for each subsequent revolution of the minute wheel, the transmission wheel makes a bolphe on / i2, which should correspond to the number of raised teeth of the ridge 6, which increases with each revolution {from the first to the twelfth) minute wheel, corresponding to the number of beats; hammer 7 /. The rise of the ridge is due to the fact that it is located; on the gear wheel 9 pin JO presses on pin 8, entailing the comb 6. The tooth 3, which is equipped with
втулка минутного колеса, нажимает на пластинку 4, снабженную штифтом 5, а этот последний нажимает на рычаг 7 и тем самым отклон ет штифт Sot штифта W. При разъединении указанных штифтов 8 и 7(9 гребень 6 под действием спиральной пружинки 28 падает, враща сь по часовой стрелке, до первоначального tjfoложени и при своем вращении действует зубцами на молоточек 7 7, который и производит удары по звонку.the bushing of the minute wheel presses the plate 4 fitted with a pin 5, and the latter presses the lever 7 and thereby deflects the pin Sot of the pin W. When these pins 8 and 7 are disconnected (9, the tongue 6 under the action of the coil spring 28 falls, rotating clockwise, before the initial tjfo-attachment and at its rotation, acts with the teeth on the hammer 7 7, which produces blows on the bell.
Дл того, чтобы бой был равномерный, применено следующее устройство. Пластинка 7 . вращаетс вокруг оси 19 и снабжена коленчатым рычагом 16, шипом 18 и пластинкой 14 с осью вращени 20 и штифтом 75. При вращении вверх (против часовой стрелки) зубцы гребн 6 поочередно приподнимг ют штифт 75 или шип 18 и свободно ароход т под ними. В то же врем коленчатый рычаг 12 молото а 77 отодвигаетс влево. При падении гребн 6 его зубец Зс1хватывает шип 75 пластинки 14. Пластинка 13 поворачиваетс так, что левый ее конец опускаетс , и рычаг 16 скошенным концом попадает между зубцами колеса 17, именЬщего семнадцать зубцов и насаженного на продолжение оси секундного коIn order for the battle to be uniform, the following device is applied. Record 7. rotates around axis 19 and is equipped with a crank lever 16, a spike 18 and a plate 14 with an axis of rotation 20 and a pin 75. When rotated up (counterclockwise), the teeth of the ridge 6 alternately raise the pin 75 or spike 18 and freely move under them. At the same time, the crank lever 12 of the hammer 77 is moved to the left. When the crest 6 falls, its prong Zs1 grabs the thorn 75 of the plate 14. The plate 13 rotates so that its left end is lowered, and the lever 16 with the bevelled end falls between the teeth of the wheel 17, which is seventeen teeth and