Claims (1)
RIVENDICAZI 1).Ogni autorotante spinto da braccio lungo di leva, arcuato o angolato,in trazione di corda o asta attac cata a cerchione di ruota(o cerchio,o circonf.za, con la punta appoggiata o meno su raggio," braccio lungo '' a sua volta premuto, da asta in direzione del centro,su bicicli piantati sul cerchione,o su altro cerchio o circonferenza di ruota,portatori di aste con tirante(molla stirata e/o peso e/o martinetto o altro tirante elastico)e con corda a cinghia incrociata(incrociate)o lineare,diritta o trasversale cοn lo senza ganci o corda distrascinamento.
2)Come sopra al n.1),ma coi biciclia 180°,tuttavia non allineati rispetto al tirante.
3)Leve da bicicli (quattro)ai lati di figura quadrangolare e bracci corti a pressione di quelli(corti dell'altra parte,ma più lunghi,e tiranti sui bracci lunghi e cerchione di ruota tirato da corde ai lati.
4)Come sopra al n.3),con tirante e pesi,ganci di tra scinamento o corda e corde anticentrifugazione-pesi.
5)Romboide coi tiranti ai vertici mobili e ganci ai lati del cerchione della ruota interna.
6)Come sopra al n.5),ma con tiranti doppi dall'anello centrale ai bicicli degli angoli e ai lati e ganci ο corda sul cerchione della ruota contro i tiranti.
7)Rombiodale su due cerchioni di ruota,o ruote con= centriche con aste raggi,per accettare la pressione dei lati lunghi e tiranti sui lati corti,come sopra ai nn.5),e 6).
8)Leve diprimo tipo con corde eccentriche su cer -chione interno o esterno all'altro portatore dei due tiranti ai polie raggi angolati per sbilanciare.
9)Come sopra al n.7),ma su ruote concentrcihe e pres= sione appoggio dall'una all'altra,senza bicicliagli angoli,ma solo appoggi mobili.
10)Esagono con snodi agli angoli e due tiranti sui lati opposti dal centro,cerchione di una o due ruote concentriche,medesime o alterne negli appoggi del tirante delle corde dalla parte in espansione e corda centrale per stabilizzare una parte.Esagono o pentagono,o altra figura geometrica.
11)Come sopra ai nn.7),e 9),ma con corda dai lati lunghi ai lati del cerchione da sbilanciare con la espansione del romboidale coi tiranti sui lati corti.
12)Come sopra al n. 11),ma su due ruote concentriche sia medesime che alterne,nella.pressione,e ganci._ 13)Come sopra ai nn.1) e 2),ma coi bicicli differen= ziati per livellare la corda che unisce le pressioni. delle aste col tirante e peso.
14)Come sopra al n.10,ma su un solo cerchione di ruota unica,o su due concentriche come al n.10.
15)Un solo angolo mobile con cuscinetto a sfere o doppio appoggio a incastro mobile di due aste parallele portatrici sul braccio lungo di tirante con o senza peso e spinta reattiva appoggiata dall'altra parte del cerchio sul quale è fulcrato il braccio mobile,con o senza appoggio o gancio su un anello centrale o ruota concentrica. CLAIMS 1). Each self-rotating lever pushed by a long lever arm, arched or angled, in traction by a rope or rod attached to a wheel rim (or circle, or circumference, with the tip resting or not on a spoke, "long arm '' in turn pressed, by the rod towards the center, on bicycles planted on the rim, or on another rim or wheel circumference, bearing rods with tie rod (stretched spring and / or weight and / or jack or other elastic tie) and with crossed (crossed) or linear, straight or transversal belt rope with no hooks or untangling rope.
2) As above in n.1), but with the 180 ° bicycle, however not aligned with respect to the tie rod.
3) Levers from bicycles (four) on the sides of a quadrangular figure and short pressure arms of those (short on the other side, but longer, and tie rods on the long arms and wheel rim pulled by ropes on the sides.
4) As above in n.3), with tie rod and weights, tow hooks or rope and anti-centrifugation ropes-weights.
5) Rhomboid with tie rods at the movable vertices and hooks on the sides of the rim of the inner wheel.
6) As above in 5), but with double tie rods from the central ring to the bicycles of the corners and sides and hooks ο rope on the wheel rim against the tie rods.
7) Rombiodale on two wheel rims, or con = centric wheels with spoke rods, to accept the pressure of the long sides and tie rods on the short sides, as above in nos. 5), and 6).
8) First type levers with eccentric cords on the inner or outer rim of the other bearer of the two tie rods at the poles and angled spokes to unbalance.
9) As above in n.7), but on concentric wheels and support pressure from one to the other, without bicycles at the corners, but only mobile supports.
10) Hexagon with joints at the corners and two tie rods on opposite sides from the center, rim of one or two concentric wheels, the same or alternating in the supports of the string tie on the expanding part and central string to stabilize a part. other geometric figure.
11) As above in nos. 7), and 9), but with a rope from the long sides to the sides of the rim to be unbalanced with the expansion of the rhomboid with the tie rods on the short sides.
12) As above in n. 11), but on two concentric wheels, both the same and alternating, in the pressure, and hooks. rods with tie rod and weight.
14) As above in n.10, but on a single rim of a single wheel, or on two concentric ones as in n.10.
15) A single movable corner with ball bearing or double movable interlocking support of two parallel rods bearing on the long tie rod arm with or without weight and reactive thrust resting on the other side of the circle on which the movable arm is pivoted, with or without support or hook on a central ring or concentric wheel.