DE9830C - Constantly working plan stove - Google Patents

Description

1879.

Class 1.

OSCAR PETERSEN in BRESLAU. Storsplan stove with a steady effect.

Patented in the German Empire on July 23, 1879.

This continuous material plan consists essentially of the following parts:

1. The base frame. The same consists of two transverse feet α and two mortised basic pillars c.

On the left-hand base column, towards the inside, there is the screwed-on iron material plate d with a line slot for the fabric frame cap e, the channel support / and above the control shaft bearing g; the spiral spring h is placed on the outer side.

Inside the right-hand base column there is also the line slot d, the channel support / and the control shaft bearing g ; äufseriich but the chair is i, together with the operating wavelength k with three-stage lifting screw /, m operation plate and flywheel η mounted.

2. The fabric frame. The same, 0, between the two grand columns, has on its short legs, outwardly, a conduit cap e, 1 cm thick. The cable cap on the left-hand side has adjusting nut and prefmnut p to attach to it, as well as adjusting nut and prefmut q to regulate the tensile force of the already mentioned spiral-shaped material spring at the outer end; while the cable cap on the right is attached by means of a pair of scissors or a fork,. Lever arm r (lying upwards from below), coupling bolts and the three-stage lifting screw have to move the fabric frame.

In addition, two tin drums s (22 cm long, 22 cm diameter and 2 mm slope) are located in the fabric frame from pin to pin 67 cm apart; the right-hand drum has an elongated pin to the rear, on which, outside the fabric frame and screwed with two nuts, sits a 56-stage gear t , 18.3 cm in diameter. In the latter two insert latches engage, and is an insertion pawl ν on the fixed Wassergerinne stored, so that if the Stofsrahmen is extracted ^(] / ₄ as a tooth width more) the drum by one tooth move backward PUFA, whereas the second insert pawl w , mounted on the movable fabric frame, falls into the next tooth and holds this position during the process.

The drum on the left has an adjustable pivot bearing at the front to prevent the downward hanging Tarpaulin load to be overcome by only slightly disassembling the front drum pins respectively to regulate.

Similar to a drive belt, stretched over both drums, there is the 20, s cm wide washing tarpaulin without end χ made of rubber canvas, which is kept taut from below by an adjustable tension roller and runs along the upper level of the tin drums on a tarpaulin table u, which is also on the fabric frame 0 is attached and below has two tightly placed water channels, which lead the admitted water by means of three holes through and onto the tarpaulin table, respectively. whereby the same is passed under the washing tarpaulin and spread out by means of an incision, similar to the oil supply with a peg, so that the tarpaulin, as it were floating on water, cannot stick, but also wear friction is almost completely eliminated.

So that the armored fabric frame can move easily and freely and can be adjusted at any angle, an iron adjusting shaft ζ is mounted on the heads of the stove columns, from which the fabric frame is suspended by means of three hooks 1 (there are two on the right) and inclined at will by means of an iron adjusting screw 2 will.

3. The water channel 3. The same is located just above the washing tarpaulin, stored on the right and left in the above-mentioned channel supports / on the basic pillars. It is connected to the aforementioned adjusting shaft ζ 5 by means of two hooks 4, so that lifting or lowering also takes place at the same time as soon as the tarpaulin angle is changed. It is used to apply the ore flours to be washed to the washing tarpaulin, but also to apply the light water for purifying and washing the ores during the continuous passing of the tarpaulin covered with ore.

For this purpose there is a section at the left-hand end of the channel, whereupon the compaction hopper 6 is set and the ore meal is introduced. Located to the right there are four water outlets for light water outlets, each with a protective cover; further is In front of each outflow opening there is a high-heeled board 7 to keep the outflowing water evenly to spread before it passes the washing tarpaulin. '

Claims (1)

The purpose of the compaction funnel is to remove the ore slurry which z. B ausfliefst from a Klassificätor so that Austragestrahl DAF _^3/4 water and '/ ₄ Erzmehl is to receive, to clarify and only the' / ₄ Erzmehl together with '/ to lead Ausdrückwasser for application to the tarpaulin washing; on the other hand, the ~ j _A clarified water, as an overflow from the said funnel, to be poured into a waste pipe 8 provided for this purpose and fed to the wild flood. This stove requires a compacted ore flour application. At the left-hand end of the water channel there is another water compartment with a sieve cover, from which a zinc pipe q is used as a rinsing shower. serving the washing tarpaulin, drawing the required water; Finally, close to it is the drainage pipe, in order to prevent the water channel from overflowing. Opposite the five heeled boards on the water channel there are four ore types recording boards 11, which are attached to the tarpaulin table in front of the washing tarpaulin. Pour the same into a trough-like feed or transfer sheet 12 and thus lead the obtained Ore types to the collecting vessels. There is also a channel 13, resting on two supports 14, attached, which is not only mentioned as a storage point Ore transfer plates are used, but can also be used as wild flood drains at the same time. Pat τ claim: A fabric frame that can be moved lengthways with a small plan stove. 1 sheet of drawings.