Elektrisch beheizbare Wärmflasche mit vertieft in die Flasche eingebautem
Anschlußkontakt. Bei elektrisch beheizten Wärmflaschen, bei denen gewöhnlich der
Stromanschluß mittels eines Steckkontaktes erfolgt, konnte bisher durchweg die Beheizung
nur bei geschlossener Flasche erfolgen, und da hierbei jede Kontrolle über den Grad
der Beheizung fehlt, bestand leicht die Gefahr, daß die Flasche zu stark beheizt
wurde, und daß dadurch Dampfentwicklung bis zur Explosionsgefahr eintreten konnte.
Man hat zwar bereits den Kontakt derart in die Flasche eingesetzt, daß er nach außen
nicht hervorragt, dadurch aber den- erwähnten Mißstand nicht beseitigt. Gemäß der
Erfindung soll jede Überheizung und Explosionsgefahr dadurch ausgeschlossen werden,
daß die Flasche nur bei geöffneter Verschlußschraube beheizt werden kann so daß
also einerseits die eintretende Dampfentwicklung sofort den Augenblick anzeigt,
wenn eine weitere Beheizung zwecklos ist, und anderseits eine Drucksteigerung im
Innern der Flasche und damit eine Explosionsgefahr unter allen Umständen ausgeschlossen
ist.Electrically heatable hot water bottle with built-in in the bottle
Connection contact. In the case of electrically heated hot water bottles, where usually the
Power is connected by means of a plug contact, so far the heating could be used throughout
can only be done with the bottle closed, and since this means that there is no control over the degree
If there was no heating, there was a slight risk that the bottle would be heated too much
and that this could lead to the development of steam up to the risk of explosion.
It is true that the contact has already been inserted into the bottle in such a way that it faces outwards
does not stand out, but this does not eliminate the above-mentioned deficiency. According to the
Invention, any overheating and risk of explosion should be excluded by
that the bottle can only be heated when the screw plug is open so that
so on the one hand the occurring steam development immediately indicates the moment,
if further heating is pointless, and on the other hand an increase in pressure in the
Inside the bottle and therefore a risk of explosion excluded under all circumstances
is.
Der Erfindungsgegenstand ist auf der Zeichnung in einem Ausführungsbeispiel
im Längsschnitt dargestellt.The subject of the invention is shown in the drawing in an exemplary embodiment
shown in longitudinal section.
Man erkennt hieraus die in bekannter Weise aus Blech hergestellte
Wärmflasche a, welche oben in der :litte derart ausgeschnitten ist, daß hier ein
besonderer Behälter b eingebaut werden kann, welcher in das Innere der Wärmflasche
hineinragt, und der zur Aufnahme des elektrischen Heizkörpers c dient. Derselbe
wird auf dem Boden des Behälters b durch die Verschraubung d festgehalten, während
das Füllrohr e wasserdicht hindurchgeführt ist. Der Behälterb ist durch einen besonderen
festen Deckel f abgeschlossen, und an diesem Deckel sitzt ein Stutzen g, welcher
als Träger für den Steckkontakt h dient. Letzterer vermittelt die Stromverbindung
mit dem elektrischen Heizpörper c und sitzt in bekannter Weise so tief, daß er nach
außen nicht hervorragt.One recognizes from this the one made in a known manner from sheet metal
Hot water bottle a, which is cut out in the litte above in such a way that here a
special container b can be installed, which in the interior of the hot water bottle
protrudes, and serves to accommodate the electric heater c. Same
is held on the bottom of the container b by the screw connection d while
the filling tube e is passed through in a watertight manner. The container b is special
Fixed cover f completed, and on this cover sits a nozzle g, which
serves as a carrier for the plug contact h. The latter provides the power connection
with the electric heater c and sits in a known manner so deep that he after
outside does not stand out.
Der Füllstutzen eist durch eine Verschlußschraube i verschließbar.
An dieser Schraube i
sitzt eine passend gebogene Scheibe k, welche so weit
übergreift, daß der Steckkontakt h von ihr vollständig überdeckt wird. - Infolge
dieser Einrichtung kann die Verbindung mit der Stromleitung nur dann erfolgen, wenn
die Schraube i abgenommen ist. Alsdann aber ist auch das Füllrohr e oben offen,
und etwa auftretende Dämpfe können durch das Entlüftungsrohr l ungehindert ausströmen.
Das Auftreten von Wasserdampf zeit mithin auch gleichzeitig an, wann die vollständige
Erwärmung des Wasserinhalts beendet ist, wobei gleichzeitig jede Gefahr der Explosion
ausgeschlossen ist.The filler neck can be closed by a screw plug i . On this screw i sits a suitably curved washer k which overlaps so far that the plug contact h is completely covered by it. - As a result of this facility, the connection to the power line can only be made when the screw i is removed. But then the filling tube e is also open at the top, and any vapors that may occur can flow out unhindered through the vent tube l. The occurrence of water vapor therefore also occurs at the same time as when the complete heating of the water content has ended, with any risk of explosion being excluded at the same time.