DE1913052U - ENCLOSURE FOR TELEVISION RECEIVER. - Google Patents

Description

RA.033 376 * 21.1.65

IMPERIAI radio and television company G.m.b.H. Osterode / Harz.

Housing for former television receivers «P-132.

Firing primarily relates to the housing for television receivers. With wooden cases for this purpose, it is common to have the surfaces of the case covered with veneers (made of Wood or precious wood) and apply a lacquer layer over the veneer, which after drying is then added Must be subjected to grinding and polishing process *

Housing of this type - in addition to the advantageous appearance - also have considerable disadvantages, which are primarily Line express themselves in the sensitivity of the surfaces to impact or friction, so that in most cases an expensive Packaging is required. However, as experience shows, housings for television receivers must also be provided if necessary for repeated transports, e.g. "B" for repairs etc. with Emergency packaging must be well suited, with no surface damage caused by scratches or pressure marks, if possible should.

In some cases, a Housing made of sheet metal with front part (and rear wall) made of plastic used. However, this technique is not suitable for TV receivers of a stationary type, in which also to the

acoustic properties of the housing very high demands be asked.

The purpose of the innovation is a television set, especially for domestic use, whose housing is, for example, in the

See, proven wood technology is made, but in his Training and arrangement of the housing surfaces a Surprisingly advantageous connection with coverings or also coverings, preferably with plastic foils, enables «

The housing for television receivers, preferably in the G-round design made of wood, is essentially marked through training and development in which G-ehäusetei-Ie with surfaces or edges made of wood with those that have coatings made of plastic foils, connected in the same housing are.

In an advantageous embodiment according to the furnace, the housing of the television receiver has a design in which the plastic picture frame is used as a pressed part an upper part (housing cover) made of wood and wood veneer and the two side surfaces are connected with coatings of plastic foils in the same housing.

According to one feature, the upper part or the housing cover is e.g. using edge strips, designed in such a way that with slightly protruding edge strips, a protection (and closure) the edges of the film attached to the side surfaces are reached in a similar way © the edges of the film on the side surfaces, which can reach up to the picture frame, attached in such a way that a protection of the edges of the film by the picture frame or / and is ensured by the operator badge.

The protection and closure of the housing at the bottom is made according to a further feature with the aid of a skirting board Wood has the effect that there are no disadvantages or disturbances to be feared from open foil edges.

* ~ 3 -

The hiring can be based on the exemplary embodiment described are arranged, with also further features of the price increase based on a picture of the housing in more detail are described.

As can be seen from the figure ~ view of the housing diagonally from the front - the housing, which is made of wooden panels can be made, the picture frame 3 on the front. It is beneficial to have this picture frame with a Produce support edge as a pressed part made of plastic.

The two side surfaces of the housing 2 are, as indicated in the figure, provided with coatings or pads made of plastic films, these coatings or pollen with the edges up to (or below) the picture frame 3 (left side) or up to Badge 6 of the controls and scale (right side) should be enough »A part of the front can advantageously be covered with γοη the film (5) ·

! For this purpose so-called Adhesive films on the inside have an adhesive layer, ideally suited.

The side surfaces can advantageously also be coated on the rear edge of the housing in the interior of the housing, so that (ζ · Β ·) the structure of the wood at the rear edges is covered by the foils *

The housing cover 11 may have a ff "in" 8aiiOT Ri "niBiw wood veneer on its surface. The Deekelplatte can be provided at the edges with edge strips 7 (in front and on the sides), which protrude slightly to the outside, so that a reliable protection of the Polienränder at the upper edge is achieved. The housing is closed and protected at the bottom by the strip 4.

In some cases, the training after the! Also be advantageous for such housing, which in the essential Basic design are made in plastics technology. The related! Areas can be used to protect the Coating or the film as a whole can be arranged somewhat recessed, so that the edges of the film are protected.

By designing the housing for television receivers according to the innovation, in particular based on what has been described Embodiment, the disadvantages of the polished case are completely eliminated: The otherwise very sensitive The surfaces of the side parts are covered by plastic film almost insensitive to scratches or pressure damage, and if necessary washing or cleaning the foils is easy to carry out.

Rough-grained foils are advantageous for special cases. «Foam-backed foils are also available that are largely shockproof.

The protection of the housing cover 1 is reliably effected by the edge strips 7, with an additional layer made of transparent Plastic can be attached over the polished veneer. In some cases, a metallic foil, in particular for the cover plate, which lately have also been sufficiently suitable for anterior tracks having.

. When choosing something lighter (e.g. parchment-like) Foils as a cover for the side surfaces in connection with a dark precious wood surface of the cover plate is also used next the enumerated technical advantages - a new type of housing that is effective for sales is achieved because the customers too the practical benefits of training in choosing

the recipient cannot be overlooked.

In a similar way, optical advantages, which offer the television picture an improved spatial position, thanks to the special tinting of the side surfaces of the housing. Metallic, finely patterned foils can be combined very effectively with the picture for a visual frame effect, see above that with the innovation there is also a technical basis of great importance.

Housing according to the innovation can also be used with smaller spatial dimensions, e.g. for portable television receivers built-on antenna etc. *, instead of metal housings an advantage being.

With color television, it is easily possible after the innovation. Housing in neutral tones, such as bronze or old gold, to train «In this way a collision with the pictures is avoided in any case, so that also in this respect there is a tangible benefit.

Claims (7)

RA. 033 376-21.1-65 Sohutzrechteι 1. Housing for television receivers, preferably in the basic version made of wood, characterized by a training and design, "in which housing parts with surfaces od. Edges made of wood with those that have coatings made of plastic foils are connected in the same housing. 2. Housing according to Anspruoh 1, characterized by a training country design in which the picture frame (3) from Plastic with an upper part (housing cover 1) made of wood, preferably with wood fumers, and the side surfaces (2-2) connected with covers made of plastic foils in the same housing are. 3. Housing according to claim 1-2, marked by a ^ arrangement of edge strips (7) on the housing cover (1), which are attached so that a protection (closure) of the film edges (2) is achieved. 4. Housing according to claims 1-3> gekennz eiohne t by an arrangement of the foils on the side surfaces (2-2), which are inserted into the housing while enclosing the rear edges. 5 * Housing according to claim 1-4 * characterized by an arrangement in which the edges of the film are protected by the edges of the picture frame (3) and the operating badge (6), 6. Housing according to claims 1-5, characterized by the use of plastic films that are rough ^ grained. 7. Housing according to claims 1-5, £ ekennz £ i_ehnet through the application of metallic plastic foils that have a pattern »