DE1858785U - ANY MOVEABLE BUTTON, NO LONGER SEWERABLE. - Google Patents

Description

Any relocatable button that can no longer be sewn on description description The buttons known so far (including the decorative buttons) must be sewn on or on =. Very often it happens that the button is turned off or. pulls out and the item of clothing or laundry is damaged. Especially with the new fashion, which is characterized by very large and also somewhat heavier buttons, the risk of tearing off or losing the button (which can often no longer be obtained) is much greater. Accordingly, there is also a more frequent one Sewing required; but the material suffers due to the frequent sewing of the item of clothing or laundry considerably, because the sewing takes place always in the same place. With the newly developed button, these disadvantages are easily eliminated avoided in that the new button can be attached or relocated as often as desired and without any damage to the material at any desired point on the garment in a matter of seconds.

The new button is special for the men's clothing industry valuable = full, because the gentlemen can attach and replace the button themselves.

The button is also on uniforms, work clothing and laundry items (e.g. pillows, kerchiefs, covers, etc.).

The actual button consists of a very thin plate, which comes on the inside or under the lining of the respective garment. This plate prevents the fabric from tearing out. Sitting on the plate a round, angular or oval needle, which one with a running circular groove below the needle point is provided. At the same time, the needle can also be connected to an or Make several longitudinal grooves and grains.

The needle with the plate, running round groove and point becomes once pushed through from the inside of the fabric upwards and connects with it the button upper part in which there is a slider with a spring, hole and slot. The button closes with light pressure and with a simple turn to the right the slot in the slide releases the needle with the plate again.

In the other embodiment, the lower part of the needle is buttoned (and not with plates). The needle and button go from the top of the The fabric is pushed through to the bottom. The needle point with a running round groove is inserted into the two sliders located below the fabric, which have a hole and a slot and spring are pressed in and the needle and button are held in place.

By pressing the two sliders underneath the fabric, it releases the needle with button is made of slot and hole and the needle is free.

The above Button can be made from any material and in any size.

For the clothing industry, the button is made with a guide pin, so that the material thickness (fabric, etc. can be taken into account) and a good solid one Seat of the button is achieved.

For the leather industry, the button is predominantly without a guide pin Find use because a button through. Material is not required.

Further features and advantages of the invention are evident from the enclosed Representations and the following description can be seen.

The reference numerals of the drawing are used below with reference to FIGS. 1-7 described.

Figure 1: shows the button base (7) with a round hole (2) and guide edge (8) with base (9) and guide groove (14).

Figure 2: shows the button cover upper part (16).

Figure 3: shows push-on bolt (1), round hole (2), slide push-on edge (3) Slide guide edge (4) and slide (5) with slide slot (6) and lower part (7) Leading edge (8) and base (9) as well as needle (11) with needle plate (10) and Upper part guide groove (12) as well as compression spring (13) and pressing edge (14) needle groove (17) and button cover upper part (16) as well as needle point (21).

Figure 5: shows needle groove (17) with needle (11) and needle plate (10).

Figure 6: shows another embodiment, namely button top (16) with needle (11) and needle groove (17) round hole (2) and slide (20) with slide edge (8) and slide slot (6) as well as guide groove (14) and in the slide located oval slot (18) and compression spring (13) and upper slide part (19).

Figure 7: shows the button top (16) with needle (11) and needle groove (17) and needle point (21).

By turning the upper part of the button cover (16) to the right, the push-on bolt presses) on the slide pressing edge (3) and on the spring (13) thus there is a round hole (2) running round groove (17) and needle (11) can with point (21) and running Round groove (17) pulled out of lower part (7) and base (9) as well as plate (lo) will. The button is then open.

Plate (lo) with needle (11) and point (21) as well as running round groove (17) is pushed into the base (9) and the lower part (7) into the slide (5) with a round hole (2), then spring (13) presses on slide (5) and slot (6) and pushes itself into running Round groove (17). Thus the button is closed.

Fig. 6 and Fig. 7 show the other representation.

The needle (11) with button (16) and running round groove (17) as well The needle = point (21) is inserted into the slide (19) and the slide (2o) into the existing round one Hole (2) pressed, thus spring (13) presses on slide (19) and slide (2o) and pushes the slot (6) onto the circular groove (17) and the button is held in place.

Pulling out the button (16) with the needle (11) and running Round = groove (17) as well as needle point (21) and slide (19) and slide (2o) pressed on spring, so round hole (2) comes to running round groove (17) and can be pulled out. The button is then open again.

Claims (1)

"Any relocatable button that can no longer be moved Claim 1: Knepf thereby gekenseichNet, that a slide (5) with slot (6) and raRde! E Lech (2) for & r adel (11) is provided (see Fig. 3 '. Kriopf n-ich Arisprueh lt dadurefi dekeimzeielinetp daso der S & hiber (5) a scMe press-on edge (3) md has a barrel (14) for spring (5) (e. here. Fi. 3) ' Claim 3: button na. Eh 4 map turning 1 and 2, characterized in that that a lower part (ao Pig. 1 irageaimt) with Base (9) round Fihrengslech (2) for Nael (l) <- ahgefrSteein rt r. irt) mz and plastic material (4 pieces! -) for slider (5) as well as cell guide edge (4) for button top (Fig. 2 ihsgeanmt) has. Claim4! Rßopf according to claims and 3, characterized in that daso the i; nopide cover (16 a. Vig. 1) with inverted. Knoff ruBgerand (12 see F'i. 3) and overprint bolt () s. sweet putty is. Claim 5: Hof sach claims up to 4 characterized in that that the nobility (11) sit Mttehen (10) t lace (21) anda running round belt (17) or LBgsriHB is provided. & nspru. ch 6: sopf according to asprcea 1 to 5 characterized de.die adel (11-Fig. 5) s'it KROpfspitze (21) and extending round groove (17) is provided (See also Fig., and Fig. 4). Claim 7 Knol,: t rzaeii 1 to 6 daduroli Sekerrzeich, that two slides (see Fig. 6! No. 19 and 20) other tire and titanium slot with round hole (6 and 2 for Mel (11),? ed4r (13), FMhr <mute (14) and Slot (18) for retaining bolt (2a. Fig. 6) equipped eats.