Claims (2)
b η. ν vi1 w O «J W W* · ^J* « U Blatt -1- Winkel mit Rellbandaaß 5.Io»1956 Die NMJBHDITCp der Fa. Gebrüder Kremer betrifft einen Winkel, der zum Gebrauch durch Schreiner,Bastler,Modellbauer, Dekorateure usw., in besonderer Weise ausgebildet ist. Die bekannten Winkel bestehen aus Schenkel und Stahlzunge. Im Gegensatz dazu ist der Winkel der Fa. Gebrüder Kremer so ausgebildet, dass ein Ende des Schenkels (B) als Gehäuse (C) auslaufend ein Rollbandmaß (D) enthält. ZWECK der HIeuerung ist es, den Winkel zusätzlich als Längenmaß verwenden zu können und zwar einerseits ausschliesslich als Längenmaß, indem von Punkt F aus gemessen wird, also τοη der Stelle aus, wo das Rollbandmaß aus dem Winkel heraustritt. Andererseits soll er als zusätzliches Längenmaß benutzt werden können bei gleichzeitig angelegtem Winkel, indem τοη der Innenkante der Stahlzunge (3Ξ) ausgehend oder τοη der Aussenkante der Stahlzunge (E) ausgehend gemessen wird. Für Messungen τοη der Innenkante (H) suss die länge τοη Punkt. Gi-H und für Messungen τοη der Aussenkante (E) muss die Länge Toa Punkt E-F dem Maß, welches das Rollbandmaß anzeigt, zugegeben werden. Diese Zugabemaße werden auf dem Schenkel (B) eingeprägt oder aufgestempelt, sodass diese τοη dem Benutzer des Winkels nur abgelesen und hinzugerechnet werden müssen. Der VORTEIL des Winkels liegt also darin, dass er durch die Kombination mit einem Rollbandmaß Tielseitiger und als Mehrzweckwerkzeug Terwendet werden kann. In der Zeichnung sind dargestellt: Abb.l Draufsicht des Winkels Abis.2 Querschnitt des Winkels In beiden Abbildungen ist das Gehäuse für das Rol-lbandmaß mit C; und das Rollbandmaß mit D bezeichnet. SCHÜTZANSPRUCHb η. ν vi1 w O «JWW * · ^ J *« U sheet -1- angle with Rellbandaass 5.Io »1956 The NMJBHDITCp of the Kremer brothers concerns an angle that can be used by carpenters, hobbyists, modelers, decorators, etc., is designed in a special way. The known angles consist of a leg and a steel tongue. In contrast to this, the angle from Gebrüder Kremer is designed in such a way that one end of the leg (B) contains a tape measure (D) ending as a housing (C). The PURPOSE of the renewal is to be able to additionally use the angle as a measure of length, on the one hand exclusively as a measure of length by measuring from point F, i.e. the point where the tape measure emerges from the angle. On the other hand, it should be able to be used as an additional length measure with an angle applied at the same time by measuring τοη starting from the inner edge of the steel tongue (3Ξ) or τοη starting from the outer edge of the steel tongue (E). For measurements τοη the inner edge (H), the length τοη point. Gi-H and for measurements τοη the outer edge (E), the length Toa point E-F must be added to the dimension indicated by the tape measure. These additional dimensions are embossed or stamped on the leg (B) so that these τοη only have to be read off and added to the user of the angle. The ADVANTAGE of the angle is that it can be used on the side and as a multi-purpose tool when combined with a tape measure. The drawing shows: Fig.l top view of the bracket Abis.2 cross section of the bracket In both figures the housing for the roll tape measure is marked with a C; and the tape measure is marked with D. PROTECTION CLAIM
1) Winkel mit Rollbandmaß, dadurch gekennzeichnet, dass der
Schenkel in ein Gehäuse ausläuft (C);, in welchem ein Rollbandmaß (D) untergebracht ist.1) angle with tape measure, characterized in that the
Leg ends in a housing (C); in which a tape measure (D) is housed.
2) Winkel nach Anspruch 1 dadurch gekennzeichnet, dass für
Messungen bei angelegtem Winkel die Zugabemaße τοη der Innen- oder Aussenkante der Stahlzunge, auf dem Schenkel
abzulesen sind.2) angle according to claim 1, characterized in that for
Measurements with the angle applied, the additional dimensions τοη of the inner or outer edge of the steel tongue, on the leg
are to be read.
GEBRÜDER KREMERBROTHERS KREMER
Wuppertal- CroiieabergWuppertal- Croiieaberg
GermanyGermany