Gebrauchsmusteranmeldung.
Wohnungssteckdose !
Bei Wohnungesteckdosen sind die Eontaktfedem, welche
die Stromverbindung mit den Steokeratiften herstellen,
in nach oben offene Versenke des Sockels eingesetzt.
Die Steckdose selbstwird durcheineEappe oder Platte
abgedeckt, durch welche die Steckerstifte hindarchtreten.
Bs gibt aber auch Steokdosen, beidenen der Sockel von
einem keramischen Teil abgedeckt ist, welches mit dem
Sockel mechanisch verbanden ist. Dieses keramische Teil
besitzt die Durehgangslocher fiü* die Steckerstifte.
Bei Steckdosen, welche sehr flach ausgeführt sein sollen,
wie z. B. bei der Verlegung von Stegleitungen, die saf
der Manerand in den Putz verlegt werden, bereitet es be-
sondere Schwierigkeiten, den Sockel so niedrig auszubilden,
dass der Apparat flach mit der Aossenfiaohe der Wand ab-
sohliesst. Zur Erreichung einer möglichst niedrigen Bao-
höhe der Steckdose, bei der die Kontaktfedern in nach
unten hin offenen Versenken des Sockels eingebaut Bind,
wird der Sockel erfindungegemäss so ausgebildet, dass
sich in dem über den Eontaktfedem vorhandenen Teil des
Sockels ifnuogenfür den Durchtritt der Steckerstifte
befinden, die gebenenfälls von b dem Sockel sich erhe-
benden Buchsen umgeben sind.
Jn an Abbildungen ist die neue Steckdose in einem Schnitt
(Abb. 1) und in einer Draufsicht (Anb. 2) ohne Abdeok-
platte dargestellt.
Sie Xontaktfedern 1 und 2 (Abb. l) sind in nach unten
offene jnehmungen 3 und 4 des Sockels 5 eingelegt. tuber
den Ausnehmungen 3 und 4 ist der Sockel nach oben hin ge-
schlossen und besitzt an diesen Stellen nur die Durch-
trittsoffnungen 6 und 7 für die Steckerstifte. Die Burgh-
trittsöffnungen sind @berhalb des Sockels 5 noch durch die Büchsen
9 und 9, welche in die Abdeckplatte lo eingreifen, verlängert. Die Kontaktfedem
1 und 2 treten mit den Lappen 11 und 12 ( Abb. 2 ) seitlich nach
aus sen aus dem Sockel heraus und sind hier zusammen
mit den AnSchlussklemmen au aen auf der Oberseite des Sockels
befestigt.
Utility model registration.
Apartment socket!
In the case of apartment sockets, the contact springs are which
Establish the power connection with the Steokera pins,
inserted into recesses in the base that are open at the top.
The socket itself is through a folder or plate
covered through which the connector pins step back.
But there are also Steok boxes, both of which have the base of
a ceramic part is covered, which with the
Base is mechanically connected. This ceramic part
has the through holes for the connector pins.
For sockets, which should be very flat,
such as B. when laying ribbon cables, the saf
the manerand is laid in the plaster, it prepares
particular difficulties in making the base so low,
that the apparatus is flat against the wall.
sohless. To achieve the lowest possible Bao
height of the socket at which the contact springs are in
Recess of the base, open at the bottom, built-in bind,
the base is designed according to the invention so that
in the part of the
Base ifnuogen for the passage of the connector pins
are located, which may rise from b the base
sockets are surrounded.
In the pictures the new socket is in a cut
(Fig. 1) and in a top view (Annex 2) without cover
plate shown.
They xcontact springs 1 and 2 (Fig. L) are in down
open openings 3 and 4 of the base 5 inserted. tuber
the recesses 3 and 4, the base is upwards
closed and has only the through
openings 6 and 7 for the connector pins. The Burgh
openings are @above the base 5 by the sleeves 9 and 9, which engage in the cover plate lo, extended. The contact springs 1 and 2 move laterally with the tabs 11 and 12 (Fig. 2) out of sen out of the base and are here together
with the connection terminals on the top of the base
attached.