Beschreibung.
Gelenk - Haltearm fUr Arbeitsplatzbeleuöhtung
Bekannt ist das Bestreben, durch entsprechende Gestaltung der
Halte-
vorrichtung fSr Beleuchtung an stationären Arbeitsplätsen (Maschinen,
aferk-
bätnke, Zeicheabretter öd, dgl.) die SSlichkeit zu ehalten,
diese Arbeits-
platsbeleuchtung innerhalb eines bestimmten Aktionoradius verstellen
zu können
und an jedem Punkt innerhalb desselben, möglicherweise sèlbErthemmend,
verharzmm
lassen zu kannen.
Dae Neue der Einrichtung besteht darin, daß gebogene aohre
1, durch
welche das Stromkabel 2 gefHhrt wird, zu Gelenken ausgebildet
sind und durch
SpaaBm&tteya 3 BusassengehalteB werden und derartig arretiert
werden k8aen,
daß die Stellung der Arbeitsplatsbeleuchtung innerhalb eines
bestimmten Aktions-
radius allseitig schwenkbar geändert werden kasn, ohne die
Arretierung vorher
zu lösen oder nachher zu festigen, sodaß die Einrichtung dadurch
selbsthemmend
wird. Der Rohrblegungeradius R ist groß genug besehaffen, dssit
sich die Torsion
des stromkabels 2 nicht schädlich auf dasselbe auswirken kann.
Die Hülse 4 ist
so beschatfen, daß eine nachträgliche Montage von liandlampen
oder irgendwelcher
anderer als Arbeitsbeleuchtung sich eignender BeleuehtungskSrpr
abglich ist.
Die Befestigung der Einrichtung am Arbeitsplatz geschieht je
nach den Erfor.
deraiesen vermittels Flansch, Zwinge od. dgl.
Auf der Zeichnung ist folgendes dargestellt :
Pi.lzeigteineSeitRsaaichtdfr Einrichttmg,
Fig. 2 zeigt eine Drauf'sicht der Einrichtung,
Fig. 3 zeigt einen Längssohnitt Â-A einer Spssnautter 3 und
zweier EndeR der Rohre l,
Fig. 4 zeigt einen ngsschnitt B-B und einen Qttersehnitt C-C
der mise 4.
Description.
Articulated holding arm for workplace lighting
It is known to strive, by appropriate design of the holding
device for lighting at stationary workplaces (machines, aferk
bätnke, drawing boards, etc.)
to be able to adjust platform lighting within a certain radius of action
and at every point within it, possibly self-inhibiting, resinified
to be able to leave.
The novelty of the device is that curved aohre 1, through
which the power cable 2 is guided are formed into joints and through
SpaaBm & tteya 3 bus passenger salaries and can be locked in such a way,
that the position of the workstation lighting within a certain action
The radius can be swiveled in all directions without the lock beforehand
to loosen or to consolidate afterwards, so that the device thereby self-locking
will. The tube laying radius R is made large enough that the torsion can be avoided
of the power cable 2 cannot have a detrimental effect on the same. The sleeve 4 is
shading so that a subsequent installation of liandlampen or any
other than work lighting suitable BeleuehtungskSrpr is coordinated.
The attachment of the device at the workplace happens depending on the requirements.
deraiesen by means of flange, clamp or the like.
The following is shown on the drawing:
Pi.l shows a side room for furnishing,
Fig. 2 shows a top view of the device,
Fig. 3 shows a longitudinal part-A of a Spssnautter 3 and
two ends of the pipes l,
4 shows a longitudinal section BB and a horizontal section CC
the mise 4.