Vollautomatischer Ventilsack-Verschluß
Die Neuerung betrifft einen Ventilsack, wie er zum Verpacken
vonfain-und grobkörnigen Füllgütern Verwendung findet*
Die VentilSteaung nach erfolgter Füllung vollautomatische
hermetisch und dauerhaft zu varschlieSen ist hierbei das
Pri) Problem*.
Vorhandena Losungen verlangen, und bedürfen aine Vervollkommnung.
Die Neuerung betrifft eine neue Lösung des Problems.
Sie besteht in folgendem :
3m die hinteren Teile der oberen und unteren Ventil-
zongenverstärkang an der wirksamsten Stelle, nämlich
in der Mitte derselben parallel zum Fa stu-tzen ist
ei Spannkorper angebracht. Die hinteren Teile der
genannten Ventilzungenveratärkong aind vertikal zum
Bullatutzen gaamtet Der FSllatu. tzen besitzt einen
Führmigsansachnitt.
Die Wiritmgaweiae un die Beschaffenheit der Neuerung iat in
der Zeichnung dargestellte
Es zeigen : Figur 1 Zustand während dem Füllprozeß ;
Figur 2 Zustand nach dem Füllprozeß
Figur 3 Stutzen mit Führungaausschnitt ;
Figur 4 Ventilzungenverstärkung mit
SpannkSrper und Nutung.
Nach der Neuerung ist um die oberen (a) und unteren (a. 1)
Teile
der Ventilzungenverstärkungt in der Mitte derselben parallel
Mm FSllstutzen, beide hinteren Teile zur Hälfte umschließende
ei&SpaankSrper (b) angebracht. Beide Teile der Ventilzungen-
veBstartasmgsiad ander bezeichneten Stelle (o) genutet. In
der2ed. chnung veranschaulicht (d) den Baumenanaachnitt der
ei&ahnelles Aufklappen der VentilSffsong unterstützte
@ Zappw de rstützb
Die Wirkungsweinew Beia Aufstecken den Sackes &leitet dar
Spa=-
&3rpe M, sich dehnend (Zigar-1 b) nod dadurch die Ventil-
SfffNMjg Bigebend, in den PahFungsanaso&sitt des Pullstutzens
( ? igu. c und der FSllprozea vollzieht sich ohne Behinderung.
Nacdeatr Abziehen des gefüllten Sacken vom yailstutzen springt
deaaatB'pe. p (), beide Teile der Ventilzungeawerstärkans
ausaamespBeseead (Figur 4.) und damit die VentiISffhung wieder
du verschueseads, in seine
dias2Sagks'af des SpannkSrpers biegt die genuteten Teile (c)
der Vestilzungenverstärkung um (Figur 2) nad der hermetische
? epsohlu& ist hergestellt, vollautomatisch. Die Bemessung
der
Zugkraft des Spanhkörpers, die beliebig verstärkt werden kann,
richtet sich nach der Beschaffenheit des Füllgutes.
Scjmtzanaprüche siehe Blatt 2
Fully automatic valve bag closure
The innovation relates to a valve bag, as it is used for packaging
of fine and coarse-grained products are used *
Ventilation is fully automatic after filling
That is what hermetically and permanently closes
Pri) problem *.
Require existing slogans and need to be perfected.
The innovation concerns a new solution to the problem.
It consists of the following:
3m the rear parts of the upper and lower valve
zongen gain in the most effective place, namely
in the middle of it is parallel to the leg
attached to a clamping body. The rear parts of the
called Ventilzungenveratärkong aind vertical to
Bullatutzen gaamtet The FSllatu. tzen owns one
Führmigsansachnitt.
The Wiritmgaweiae un the nature of the innovation iat in
shown in the drawing
They show: FIG. 1 state during the filling process;
Figure 2 state after the filling process
FIG. 3 nozzle with a guide cutout;
Figure 4 valve tongue reinforcement with
Clamping body and groove.
After the innovation is around the upper (a) and lower (a. 1) parts
the valve tongue reinforcement is parallel in the middle thereof
Mm FSllstutzen, half enclosing both rear parts
egg & spaank body (b) attached. Both parts of the valve tongue
veBstartasmgsiad grooved at the point indicated (o). In
der2ed. drawing illustrates (d) the tree section of the
A similar opening of the VentilSffsong supported
@ Zappw de rstützb
The effective wines Beia put on the sack & leads the Spa = -
& 3rpe M, stretching (cigar-1 b) nor thereby the valve
SfffNMjg Bigebend, in the PahF Anaso & sitt of the Pullstutz
(? igu. c and the FSllprozea takes place without hindrance.
Nacdeatr pulling the filled sack from the yail socket jumps
deaaatB'pe. p (), both parts of the valve tongue reamer
ausaamespBeseead (Figure 4.) and with it the ventiISffhung again
you verschueseads, in his
dias2Sagks'af of the clamping body bends the grooved parts (c)
the reinforcement of the tongues around (Figure 2) nad the hermetic
? epsohlu & is manufactured, fully automatic. The dimensioning of the
Tensile force of the chip body, which can be increased as required,
depends on the nature of the product.
Scjmtzana claims see sheet 2