It's been a long time in the pipeline, but finally Thunder Under Mount Silence, the first Oakbound boxed game (if you don't count Tripods!) is on the doorstep. I've cut 98 sheets of nice, thick, glossy dungeon tiles, just two left to do! The artwork on the tiles was produced by photographing 3-dimensional pieces I had made, so I thought it would be fun to photograph some scenes on them. The walls aren't very high and in places the perspective has been forced in order to read better from above, but I think they're quite fun little vignettes.
blog header
Showing posts with label oakbound underground. Show all posts
Showing posts with label oakbound underground. Show all posts
Monday, 10 March 2025
Monday, 5 September 2016
Shelving, doors and a big hole in the floor!
Over the weekend I managed to crack on with some of the dungeon rooms.
The library is now almost finished, apart from finishing off the stone work, putting the fire and chimney in the inner sanctum and picking out a few more coloured books.
The staircase was a pain in the backside to assemble and the cause of much swearing and cursing! It seemed once it got beyond about 40mm high any further layers just wouldn't stick. In the end I used superglue rather than pva to finish it and once it was in place liberally coated the pillar with glue. It seems to have held.
The edges of the floor and the balcony I washed with woodstain to darken them. There's a doorway hidden in the top left, but will the adventurers notice it in the gloomy corner of the library?
Here's a shot with the removable side panel attached. I've yet to paint the big doorway and add the free-standing shelves to either side of it.
Next up, the ramparts/courtyard. The idea is to have an open space to serve either as an entrance/exit from the dungeon or so adventurers can get their bearings in the labyrinthine tunnels. Lots of barrels and sacks strewn across here, a trough and a well for water as well as numerous doorways leading back into the caverns.
Spraying some resin cast doorways.
And the next big room. The idea for this one is an underground lake or cistern. I started off by applying my resin cast tiles to the areas in front of the doorways, giving the impression of the remains of a richly tiled room.
Around these I painted pva and applied liberal amounts of sand, this would form the boundary of the lake area.
Next I sprayed the exposed polystyrene in the centre with black primer, melting it away.
The trick is not to spray so much it eats right through the styrene! Once I was happy with the amount that had been dissolved I mixed some paint and PVA and painted a base colour onto the bed of the lake. This seals the polystyrene to prevent the resin I would pour into it from further eating away the surface (and then pouring out all over the workbench!) Once this was dry I mixed up my clear resin and poured it up to the level of the sand. Then I checked it a few hours later before going to bed, all looked level and clear and not eating away the styrene, all good.
This morning, when I checked, I saw disaster had struck overnight! Instead of a nice, clear lake I had a foamy mass of bubbles! Rock-hard bubblebath foam! Ah... The material I had left in the pot to test curing without touching the pour had set just fine, so it wasn't a problem with the resin, ambient temperature or moisture level. I think what must have happened is that as the resin cured its exothermic reaction caused the styrene to emit gas, which managed to get through the layers of paint and glue and bubble up through the resin. Not the effect I was looking for! I did have an idea on the way into work this morning however, I'll have to have another look when I get home. It might be that this unexpected issue has prompted a whole new aspect to the relationship between the gnomes and goblins who live in this mountain!
The door castings have been much more successful. The dark strip on these is where I have poured resin with an iron filler powder into the mould. This is magnetic (see small magnet stuck to left door) and with magnets set into the door frames on the dungeon boards this will provide my magical hinge solution. Now I just need to order a shed load more magnets!
The library is now almost finished, apart from finishing off the stone work, putting the fire and chimney in the inner sanctum and picking out a few more coloured books.
The staircase was a pain in the backside to assemble and the cause of much swearing and cursing! It seemed once it got beyond about 40mm high any further layers just wouldn't stick. In the end I used superglue rather than pva to finish it and once it was in place liberally coated the pillar with glue. It seems to have held.
The edges of the floor and the balcony I washed with woodstain to darken them. There's a doorway hidden in the top left, but will the adventurers notice it in the gloomy corner of the library?
Here's a shot with the removable side panel attached. I've yet to paint the big doorway and add the free-standing shelves to either side of it.
Next up, the ramparts/courtyard. The idea is to have an open space to serve either as an entrance/exit from the dungeon or so adventurers can get their bearings in the labyrinthine tunnels. Lots of barrels and sacks strewn across here, a trough and a well for water as well as numerous doorways leading back into the caverns.
The walls were coated in PVA, had lots of cat litter pressed onto them and then a coating of paint and PVA to seal them before drybrushing. The floor still needs some washing, drybrushing and piles of scatter/gravel across it to break up the surface. I liked the bobbled polystyrene texture, so haven't disguised it with a textured paint, but it does need varying across this sized area.
And the next big room. The idea for this one is an underground lake or cistern. I started off by applying my resin cast tiles to the areas in front of the doorways, giving the impression of the remains of a richly tiled room.
Around these I painted pva and applied liberal amounts of sand, this would form the boundary of the lake area.
The trick is not to spray so much it eats right through the styrene! Once I was happy with the amount that had been dissolved I mixed some paint and PVA and painted a base colour onto the bed of the lake. This seals the polystyrene to prevent the resin I would pour into it from further eating away the surface (and then pouring out all over the workbench!) Once this was dry I mixed up my clear resin and poured it up to the level of the sand. Then I checked it a few hours later before going to bed, all looked level and clear and not eating away the styrene, all good.
This morning, when I checked, I saw disaster had struck overnight! Instead of a nice, clear lake I had a foamy mass of bubbles! Rock-hard bubblebath foam! Ah... The material I had left in the pot to test curing without touching the pour had set just fine, so it wasn't a problem with the resin, ambient temperature or moisture level. I think what must have happened is that as the resin cured its exothermic reaction caused the styrene to emit gas, which managed to get through the layers of paint and glue and bubble up through the resin. Not the effect I was looking for! I did have an idea on the way into work this morning however, I'll have to have another look when I get home. It might be that this unexpected issue has prompted a whole new aspect to the relationship between the gnomes and goblins who live in this mountain!
Friday, 26 August 2016
The library, the library, it's a place where books are free....
Getting stuck in to the dungeon creation, I've been making good use of the downtime on the laser cutters. First I drew some Celtic knot designs and grids on Illustrator, then cut them from mount board on the laser. Then I peeled away the top few layers of board to give a bass relief effect. Some I just engraved into the card to give a more subtle tile look. I chucked some silicone onto them and set about casting in resin. There's also a spiral stair section made from 6mm MDF in there.
Once I had enough resin panels I assembled them into a couple of different doorway designs, gluing them onto acetate sheets to ensure a nice, smooth section in the centre I can paint to represent the corridor beyond.
These were put into another mould, along with some panels of the reliefs to try and build up enough to do tiled flooring and walls.
Whilst the silicone was setting I put the laser to work again, this time doing parquet flooring and bookshelves for the library. It took me a fair few hours to draw up the bookcase file, but I'm very happy with the result, even the colour of the MDF is appropriate!
My plan is to cut a lot of these bookcases in 2mm to line the walls. The full case is in three 31.5mm high sections so I can put walkways between the levels in some places. Also so I can swap the levels around to prevent the effect being too repetitive. I'm also going to cut several shelves from 3mm MDF so that I can put them back to back to make little aisles, just right for studious monsters to hide in ready to leap out!
And the floor, in three sections. I'll mask it off before I work on the walls and use some panelling on the lower wall to disguise the join. The floor has to go in before working on the walls or it would scratch the surface away on the way down, it's a good, tight fit!
Wednesday, 24 August 2016
Going underground... underworld style
I recently heard news that an Underworld 5 is in the offing... hoping for a return to form after the dismal 4th film the wife and I had an Underworld marathon of the original trilogy at the weekend and I came out of it really wanting to create some terrain that's a blend of William's prison from the 2nd film and the vampire castle from the 3rd.
There's been a lot of talk around me about dungeons at the moment. After BOYL on the drive home Harry, Chris and I were discussing a dungeon bask project for next year. Then Harry's Twisting Catacombs stuff turned up (mine's still not here, boo), then Maki Games announced an imminent revival of their Modular Underground project.
With the release of 'Secrets' thoughts have turned to the next sourcebook instalment for The Woods. This will take the action to the conflict between the Gnomes and Goblins in the mountains, working title "Thunder under Mount Silence". Obviously I'm going to need some underground terrain for playtesting and photography.
We lately took delivery of a new bandsaw at work which came in an elaborate and large polystyrene box, with lots of dungeon features...
With all this happening and a few weeks of quiet summer left it would be very rude not to do something about it don't you think?
What you're looking at here is the bandsaw box chopped into chunks and surrounded with MDF (which I laser-engraved with a nice Oakbound logo for when we take it to shows). There are 8 modules measuring 45cm by 22.5cm each, giving a 3' square dungeon. Of course they can be arranged in rectangular or linear fashion as well. I figured a 3' square would be about as far as you'd want to lean to move figures. There's also a double-height section because the packing was too cool to chop up. This can add on, or displace one of the other modules which can then be stacked to give a second double-height section.
What's especially good about this size is that it means my modular board tiles which are swamp one side and cobbled the other will fit in nicely as they're 22.5cm wide and 66cm long (I can cope with the 15mm gap, might make some inserts).
The depth of each module is 12cm, with the floor depth varying between 4cm and 10cm. Now I've moaned about accessibility for play in dungeons with walls before and granted some of those areas are pretty tight. I've tried to keep as many open areas as possible and there will be lots of levels built in so the narrow spaces aren't as hard to reach. BUT I am a bit concerned about getting in to decorate, play and photograph so some of the MDF walls might be made removable once I've got the basic forms in place.
After boxing everything up I decided what I wanted each room to be. Library, cistern, council chamber, lower gatehouse etc. Actually I have two libraries because I've wanted to do something like the library from Gormeghast for some time. I then marked in lots of doors, making sure there were some standard connections and plenty of options for the feature doors, matching them in as closely as possible with the layout of the polystyrene. One of the good things about having the thick walls and different levels in there is that it doesn't matter too much if doors shift along slightly, don't line up or seem to lead nowhere. The thickness of the wall means an unseen narrow corridor, stairway or cupboard can easily be claimed.
For transport and storage these modules will stack together into a relatively tight 45cmx45cmx60cm block. I'll make a little trolley with some fixings on so it can be wheeled around for events and games at other people's houses.
Mad to start something else, especially something this big, with the planned undead army and lots of commission sculpting to get on with? Well sure, but anyone who knows me will tell you I'm never too busy to start another project... finishing, well, that's another matter. I still have a few books to bind...!
There's been a lot of talk around me about dungeons at the moment. After BOYL on the drive home Harry, Chris and I were discussing a dungeon bask project for next year. Then Harry's Twisting Catacombs stuff turned up (mine's still not here, boo), then Maki Games announced an imminent revival of their Modular Underground project.
With the release of 'Secrets' thoughts have turned to the next sourcebook instalment for The Woods. This will take the action to the conflict between the Gnomes and Goblins in the mountains, working title "Thunder under Mount Silence". Obviously I'm going to need some underground terrain for playtesting and photography.
We lately took delivery of a new bandsaw at work which came in an elaborate and large polystyrene box, with lots of dungeon features...
With all this happening and a few weeks of quiet summer left it would be very rude not to do something about it don't you think?
What's especially good about this size is that it means my modular board tiles which are swamp one side and cobbled the other will fit in nicely as they're 22.5cm wide and 66cm long (I can cope with the 15mm gap, might make some inserts).
The depth of each module is 12cm, with the floor depth varying between 4cm and 10cm. Now I've moaned about accessibility for play in dungeons with walls before and granted some of those areas are pretty tight. I've tried to keep as many open areas as possible and there will be lots of levels built in so the narrow spaces aren't as hard to reach. BUT I am a bit concerned about getting in to decorate, play and photograph so some of the MDF walls might be made removable once I've got the basic forms in place.
After boxing everything up I decided what I wanted each room to be. Library, cistern, council chamber, lower gatehouse etc. Actually I have two libraries because I've wanted to do something like the library from Gormeghast for some time. I then marked in lots of doors, making sure there were some standard connections and plenty of options for the feature doors, matching them in as closely as possible with the layout of the polystyrene. One of the good things about having the thick walls and different levels in there is that it doesn't matter too much if doors shift along slightly, don't line up or seem to lead nowhere. The thickness of the wall means an unseen narrow corridor, stairway or cupboard can easily be claimed.
For transport and storage these modules will stack together into a relatively tight 45cmx45cmx60cm block. I'll make a little trolley with some fixings on so it can be wheeled around for events and games at other people's houses.
Subscribe to:
Comments (Atom)