TWM264239U - Improvement on container cap - Google Patents

Description

M264239 4. Creation Description (1) [Technical Field] This creation is to provide an improvement of the container lid, which is mainly aimed at the lid that is overlaid on the opening of the container. Designers who reduce the cost of mold opening at the same time, and at the same time, the processed lid body has a flexible resistance when the container is fastened. [Previous technology] The industry developed and used containers and upper lids for holding articles or food. Most of them are made of acid proof and strong plastic to form a container with the required volume, and the lid (1 0) (Refer to the first picture) The injection molding of a plastic with a close characteristic is used to form a shielding section (1 0 i) that can cover the opening above the container and the surrounding can be used as a buckling paragraph (1 0 2) For the processed cover body (10), the buckle-shaped buckle sections (1002) around it can be pulled out through the middle top support post (3 0 1) and the peripheral number. Only the oblique pin (3 0 2) is used to synchronously pull the formed cover shielding portion (1 0 1) and the surrounding buckle sections (1 0 2) to exit outward, so that this type of mold has to consider the cover when opening the mold. The component design of the body (100) ejection mold causes the cover mold to have a higher mold opening cost. After the formed container is filled with articles for the user, the lid body is taken to cover the opening at the upper end of the container, and the fastening sections (102) around the lid body (10) are sequentially concavely folded toward the side wall of the container, so that The bounding portion (丨 〇3) formed by each of the buckling paragraphs (10) of the lid body (10) can impose an azimuth restriction on the stopper portion facing downward from the notch of the corresponding outer wall of the container; and the lid body (1 0) The buckling section (1 0 2) around is a complete plate, so that when the boundary part is separated from the corresponding resisting part, a considerable external force must be applied to open the cover.丨 Open [Content]

UTILITY20040621PU604.ptd

M264239

This creation is based on the disclosure of the same-sex body to overcome the implementation problems. After the model is formed, it can be easily ejected. She also covers the cover body at the buckling section corresponding to the cover body formed around the cover body. The main purpose of this creation is to have elasticity and easy removal when there is an opening above the container, and the corresponding part of the buckle that is movable and foldable along the periphery is used to open the slot; after borrowing and molding, only the middle top support is needed.枉 When the easy-to-operate ejection mechanism can be used to cover the container, it can be used to make the adjacent boundary part elastically and urgently positioned in the corresponding buckle. In addition, each buckle section is disassembled to facilitate the buckle application. When it comes to the latching part, it is flexible and easy to take. [Implementation method] The cover body designed by covering the opening period of the upper end of the container can be quickly ejected after being ejected. The cover can be elastically pressed against the openings and the cover's detachment characteristics through the slot holes opened in between. In the provision of a cover body covering the opening of the container, a paragraph 'on the border side of the adjacent side is designed to facilitate the cover body to eject the object from the outside by shooting, and the cost of mold opening is specifically reduced; When the cover body is opened from the slotted hole of each fastening section into the abutment part of the side wall of the container, the cover body can be separated from the container by being separated from the container when the cover body is opened.

The improvement of the container lid of this creative design, see the third figure, is mainly taken from the cover (1) corresponding to the cover (2) which is overlaid on the container (2) along the periphery is a buckle section (11) ), For each buckle section (11) toward the side wall of the container (2), a B-shaped boundary section (12) is formed, and the buckle section (Π) adjacent to the corresponding part of the boundary section (12) is formed with a groove for the groove The hole (丨 3 is provided through the peripheral slot of the cover (1), so that the cover (丨) can be easily formed after injection molding.

UTILITY20040621PU604.ptd Page 6 M264239

4. Creation instructions (3) Directly take the middle top brace (3 丨) ^ Remove (refer to the fourth x Μ body) for a simple and easy external operation ..., and then worse by this > F < back off To reduce the cost of mold opening. When the cover CD of the f = ^ f type is installed on the opening above the container (2) (for illustration), the slot () opened by each buckling paragraph (11) can be used to make adjacent The limiting portion (12) of the corresponding retaining wall (2) buckles on the side wall of the container (2), and maintains elastic and urgent positioning. Conversely, after removing and removing the cover (1) & Rishou, pull the end of each buckle section (11) with the outside of the hand, so that the opening has, each buckle section (11) of the hole (1 3) in When detached from the container (2), it can be smoothly dialed out from the corresponding side abutment portion (21) of the container (2) with an elastic outer turning, so as to achieve a simple buckle or remove cover (丨).

UTILITY20040621PU604.ptd Page 7 M264239

The first picture: The second picture: The third picture ... The fourth picture ... The fifth picture: The figure refers to the top plan view of the conventional cover body. The conventional cover body is used to eject the mold. Schematic drawing of the cover body withdrawing from the mold. Schematic illustration of the snapping operation of the cover body in conjunction with the container installation. [Conventional] (10) The cover body (1 0 2) buckle section (3 0 1). ) Lid body (1 2) Boundary part (2) Container (3 1) Top support post (1 0 1) Covering part (1 〇3) Boundary part (3 0 2) Oblique lock

(11) Set up paragraphs (1 3) Slots (2 1)

Claims (1)

M264239 The one-piece extension of the L-shaped boundary part is integrated with the periphery of the L-shaped boundary part. After the corresponding formation of the boundary part, it is only necessary to use a simple operation body with a container to cover the hole to make the adjacent boundary hold each of the urgent pressing When the corresponding retaining part of the paragraph is buckled, the scope of the patent application is an improvement of the container lid. The buckling paragraph with a movable concave fold is directed toward the side of the container to protrude. The improvement is that the peripheral part of the lid is opened. Slot holes; in this form, the objects are ejected out of the way by injection, and the cost of mold opening is specifically reduced; when the slot formed by each buckling section is inserted into the side wall of the container, the cover is protected. The lid can be removed from the container by opening a boundary portion with a slotted section. Including the cover, the side wall of the four containers is formed by the ejection mechanism which can be formed by the top stop post with the position of the stopper as the orientation limiter. The limiter can be used at the corresponding buckle position; and it can be disassembled to facilitate the buckle. Easy to take Page 9 UTILITY20040621PU604.ptd _ ----