Примен емые на строительстве контейнеры дл кирпича, состо щие из двух соедин емых между собой частей-поддона с крюками и футл ра с шарнирно подвешенными к нему с двух противоположных сторон рамками, имеют тот недостаток, что При установке крапом контейнера на площадку, рабочий дл сн ти футл ра со штабел кирпича, должен вручную вывести скобу из-под крюков поддона.The brick containers used in the construction, consisting of two interconnected parts of a pallet with hooks and a case with frames hinged to it from two opposite sides, have the disadvantage that These cases with a stack of bricks, must manually pull the bracket out from under the hooks of the pallet.
Насто щее изобретение устран ет этот недостаток тем, что соедин ет подвешенную рамку с подъемной скобой фзтл ра посредством пружины , котора автоматически устанавливает рамку в подн том вверх вертикальном положении.The present invention overcomes this disadvantage in that it connects the suspended frame with the lifting rod of the federal assembly by means of a spring, which automatically sets the frame in a raised, upright position.
На чертеже представлен общий вид контейнера в аксонометрической проекции.The drawing shows a General view of the container in axonometric projection.
Футл р / контей} ера надет на два поддона 2, положенных вплотную один к другому. С обеих сторон поддоны имеют крюки 3. К футл ру 1 с обеих сторон также прикреплены направл ющие скобы 4 (внизу) и 4 (сверху). По этим «анравл юнтим скобам с обеих сторон футл ра / передвигаютс вверх и вниз подт емные петли 5, к нижней стороне которых шарнирно подвешена рамка 6. Рамка 6 помимо шарнирной подвески соединена с нижней стороной каждой петли 5 спиральной пружиной. 7, котора посто нно т нет рамку кверху. На чертеже петл 5 представлена в ее верхнем положении. Нормально же при отсутствии силы, т нущей ее вверх, она под вли нием собственного веса стремитс зан ть нижнее положение. При надевании футл ра на штабель кирпича, уложенного на поддон (кирпич на чертеже не показан), когда петл 5 займет нижнее положение, рабочий ногой, преодолева сопротивление пружины 7, переводит рамку из ее вертикального положени сверх от нижней стороны петли в вертикальное же положение , а вниз-от нижней стороны петли, т. е. поворачивает ее на 180 около шарнира, тут же приподнимает петлю 5 кверху и подкладьшает штырь 8, подвешенный на цепочке 9, под перекладину 10 петли .5. В этом положении пружина 7 не может вывести )aMKy 6, вощедшую в зев крюков 3. При подъеме краном контейнера штыри 8 освобождаютс и выпадают из-под перекладины 10. Если после этого поставнть контейнер на площадку, ослабить усилие, т нушее петли 5 кверху и дать им зан ть свое нижнее положение, рамка 6 выйдет из зева крюков 3, а нр жина автоматически переведет ее в верхнее положение . После этого футл р может быть сн т со штабел без помощи рабочего.The case of the container / container is put on two pallets 2, which are placed close to each other. On both sides of the pallets there are hooks 3. To the box 1 on both sides there are also attached guide brackets 4 (at the bottom) and 4 (at the top). Using these anchors on both sides of the case, the sub-loops 5 move up and down, to the bottom of which frame 6 is hingedly hung. Frame 6, in addition to the articulated suspension, is connected to the lower side of each loop 5 by a helical spring. 7, which is constantly t frame up. In the drawing, loop 5 is represented in its upper position. Normally, in the absence of a force pushing it up, under the influence of its own weight, it tends to occupy a lower position. When putting the case on a stack of bricks laid on a pallet (brick in the drawing is not shown), when loop 5 takes the lower position, working foot, overcoming the resistance of the spring 7, moves the frame from its vertical position over from the bottom side of the loop to the vertical position, and down from the lower side of the loop, i.e., turns it about 180 around the hinge, immediately lifts the loop 5 up and lays the pin 8 suspended on the chain 9 under the crossbar 10 of the loop .5. In this position, the spring 7 cannot bring out) aMKy 6, which is waxed into the mouth of the hooks 3. When the container is lifted by the crane, the pins 8 are released and fall out from under the crossbar 10. If after this put the container on the platform, loosen the force, push the loop 5 upwards and give them their lower position, frame 6 will come out of the hook opening 3, and the receiver will automatically move it to the upper position. After this, the case can be removed from the stack without the assistance of a worker.