Гидравлические регул торы давлени газа с уравиовешенным редукциоииым клапаном, шток которого св зан с иоилавком, помещенным в сосуде, сообщающимс уравнительной трубой с переливным резервуаром , известны.Hydraulic pressure regulators for gas with a balanced reduction valve, the stem of which is connected to an ion valve that is placed in a vessel that communicates with a balance pipe with an overflow tank, are known.
Недостатком таких регул торов в.т етс то, что при каждом измс пении редуцироваииого дав.чени измен етс и 15е.чичина открыти K.I:; пана.The disadvantage of such regulators is that with each measurement of the reduction of pressure, the scale of opening K.I :; sir
Отличительной особенностью данного предложени вл етс то, что дл обеспечени посто нно ве.чнчньп) открьгги K.ianaiia при изменен ;;: редуцированр ого давлени в некоторы.х заданных предела.х поплавок посажен на шток клапана свободно п оппраетс на щток ,niiiib прп понижении уровн жидкости и сосуде до опреде.ченного предела.A distinctive feature of this proposal is that in order to ensure constant ve.chnnp) otkryggi K.ianaiia when changed ;;: reduced pressure in some of the specified limits.x float planted on the valve stem freely opposes on the stem, niiiib prn lowering the level of the liquid and the vessel to a specific limit.
Устройство предлагаемого регул тора изображено па схеме.The device of the proposed controller is shown in a diagram.
Газ с давлением Р поступает в сосуд / через входиоГ 2 клапапную коробку 3 п к.чанан 4. В сеть газ выходит через В111ходно11 патрубок 9. По мере повьнленп дав.1е11и газа как в сетп, так и в lery .| торе гюда, на;н1та до определенного уровн в регу.ч тора, по, нпмаетс в уравнительную трубу 5.С понижением уровн воды в корихсо pei-ул тора, поплавок б.свободпо насаженный на шгок 7. онускаетс . Ког да сто.чбводы в )равннтельн01 | трубе 5 достигает дна сборнпка-расшпрптс .ч //, нон,1авок6 опуска сь на опорную щайбу 10, свонм весом неремс стнт шток 7 и соединенный с ним клапан 4 вниз. Выходное отверстие ур;.п ннтельной трубы расположено на такой высоте, на которой устанав.пг «аетс уровень жидкости, соответствующий полному закрытию кланана Клапан 4, опуска сь, закрывает проход газа в корпус регул тора. Прн по11ижеп1П1 давле1П1 в регул тора поплавок всн.чывает н к.чанан 4 при noMonui нрхжииы 8 поднимаетс , открыва доступ газа в кор нус регу.1 тора.Gas with pressure P enters the vessel / through inlet 2 valve box 3 p. Chanan 4. The gas enters the network through B111 through 11 branch pipe 9. As pressure is increased, gas is 1e11 and gas is both in the setp and in the lery. The torus, here; n1ta to a certain level in the regulator, is fed into the equalizing pipe 5. With a decrease in the water level in the corihous pei-ul torus, the float is bolstered 7. It is suspended. When is it worth sto.chboda c) equal01 | The pipe 5 reaches the bottom of the assembly-rasprpsts .ch //, non, 1x6 downstairs refer to the support plate 10, with the weight of the valve stem 7 and the valve 4 connected to it down. The discharge port of the ur pipe is located at such a height at which the fluid level corresponds to the full closing of the clan. Valve 4, lowering, closes the gas passage to the regulator housing. Prn po1izhep1P1 pressure1P1 in the regulator the float takes to n Chanan 4 when noMonui Nirzhii 8 rises, opening the access of gas to the corner of the regulator.