Р б составл ющие усили копани , которые воспринимаютс измерительиой системой зуба.The components of the effort are perceived by the tooth measuring system.
Дл раздельной регистрации составл ющих усили копани иа зубе достаточно и иеобходимо выполнить полуцилиндрические выступы только в двух понеречных сечени х хвостовика , а именно - в передней и задней его част х. Действительио, если па всех четырех гран х пр моугольной измерительной части 11 хвостовика размещены тензодатчики сопротивлени , то достаточно иметь только два опорных периметра хвостовика о стенки полого корпуса, а именно только в сечени х А-А и Б-Б, а не в трех и более сечени х дл онределени ортогональных составл ющих усили копани на зубе.For separate recording of the component forces, the digging of the tooth is sufficient and it is necessary to perform semi-cylindrical protrusions only in two transverse sections of the shank, namely, in the front and rear parts thereof. Actually, if the resistance strain gauges are placed on all four faces of the rectangular measuring part 11 of the shank, then it is sufficient to have only two supporting perimeters of the shank against the walls of the hollow body, namely, in sections A-A and BB, and not in three more sections for determining the orthogonal components of the digging force on the tooth.
Так, под действием нормальной составл ющей Р п измерительна часть 11 хвостовика зуба будет прогибатьс вверх,, а противоположные грани примут форму, показанную на фиг. 1 пунктиром, и тензодатчики, наклеенные на эти грани, зафиксируют нормальную ортогональную составл ющую.Thus, under the action of the normal component P p, the measuring part 11 of the tooth shank will bend upwards, and the opposite faces will take the shape shown in FIG. 1 is dotted, and strain gauges glued to these faces will fix the normal orthogonal component.
Под действием боковой составл ющей PQ измерительна часть 11 зуба будет прогибатьс в боковом направлении, и соответствующие противоположные грани примут форму, показанную на фиг. 2, а тензодатчики, наклеенные на эти грани, зафиксируют боковую ортогональн ю составл ющую.Under the action of the lateral component PQ, the measuring portion 11 of the tooth will deflect in the lateral direction, and the corresponding opposite faces will assume the shape shown in FIG. 2, and strain gauges glued onto these faces will fix the lateral orthogonal component.
Под действием касательной составл ющей РК измерительна часть 11 зуба будет сжиматьс в продольном нанравлении, а отдельна группа из тензодатчиков, размещенных на всех четырех гран х измерительной части зуба, зафиксирует касательную ортогональную составл ющую.Under the action of the tangential component RK, the measuring part 11 of the tooth will be compressed in longitudinal direction, and a separate group of strain gauges placed on all four faces of the measuring part of the tooth will fix the tangential orthogonal component.
Наличие нолуцилиндрических выступов на всех четырех гран х хвостовика (по опорным периметрам двух поперечных сечений) полностью исключает погрещность от возможного осевого разворота зуба под действием боковой составл ющей, поскольку весь хвостовик вправо от опорного периметра оказываетс разгруженнЕзГм от осевого момента, возникающего со стороны режущей части зуба, а также уменьщаютс силы трени выступов о стенки полого корпуса.The presence of nucylindrical protrusions on all four edges of the shank (along the supporting perimeters of two cross sections) completely excludes the incidence of possible axial rotation of the tooth under the action of the lateral component, since the entire shank to the right of the supporting perimeter is unloaded from the axial moment arising from the cutting part of the tooth and also the strength of the friction of the protrusions against the walls of the hollow body is reduced.