.трон). Выход блока сраввеви 14 соединен с входом утфавл кшхего блока тагганв 16, к выходу которого аодключева цепь питани светодиода 1. Элементы 1-8 компактно соб равы в общем корпусе и образуют датчик. Остальные глементы относ тс ко вторичной аппаратуре н соединены с ним линией св зи Работа преобразовател основана на ис пользовании пьезооптического эффекта, состо шего в зависимости ДВОЙН01Ч) лучепреломлени от механического напр жени . СЧ новными причинами изменени чувствительности пьезооптического преобразовато- л вл етс зависимость от температуры светоотдачи светодиода ( С) и чувствительности фотодиода (К ) Можво показать, что чувствителадость пpeoбpaзoвiaтeл пропораиональна прозвеае вик луч«;того потока светодиода на чувствительность фотодиода. Пренебрега сравнительно малой величиной темнового тока {3f можно считать, что начальный т(ж фотодиода ( Г ) также пропо1щионален этим величинам. Следовательно , поддержание посто нной величины начального тока фотодиода прйвод1гг к сохранению посто нной чувствительности. Описанна оптическа система позвол ет при нагружевии чувствительного элемента 3 получить приращение освешенностей фотоприемников одинаковыми по величине и про тивоположны м по зваку. При линейных люкс 4мперных хара1стеристиках фотоприёмников 7 и 8 и одинаковом их начальном токе (tJ ), сумма токов фотоприем лпсов, а следовательно,, и йапр жение на резисторе 13 не зависит от из- мер емой силы Р С + Sfjit o). При изменении, например, при увеличени температуры, светоотдача светодиода падает , уменыцаетс световой поток и, как следствие, уменьшаютс токи фотодиодов 7 и 8. Падение напр жени на общем резисторе 13 уменьшаетс , на выходе блока сравнени 14 по вл етс сигнал, поступаю- щий на вход управл емого блока питани 16, который увеличивает напр жение питаки светодиода 1. Поэтому возрастает его световой поток, за счет чего увеличиваютс токи фотодиодов 7 и 8 и напр жение на резисторе 13, стрем сь к первоначальной величине. Дл плавной регулировки чувствительности пьезооптического преобразовател резистор 13 может быть выполнен переменным . Кроме ведени обратной св зи, желательно включить в цепь питани светодиода терморезистор 17 или резистор. Эта частична автотермокомпенсаци облегчает требовани к описанной выше схеме или, при прочих равных услови х, уменьшает зависимость чувствительного преобразовател от температуры. ормула изобретени Пьезооптический измерительный преобразователь содержащий источник света, пол ризационно-оптическую систему и два дифференциально включенных фотоприемника , отличаюшийс тем, что , с целью повышени точности путем уменьшени зависимости чувствительности преобразовател от температуры, он снабжен источником опорного напр жени , управл емым блоком питани источника света, блоком сравнени и сумматором выходного сигнала фотоприемников, соединенным с одним из входов блока сравнени , другой вход которогчз подключен к источнику опорного напр жени , а выход - ко входу управл емого блока питани ..throne). The output of the sravevei 14 unit is connected to the input of the uthfull kshhego tagganv 16 unit, to the output of which is the keyed power supply circuit of the LED 1. Elements 1–8 are compactly assembled in a common housing and form a sensor. The remaining elements are related to secondary equipment and are connected to it by a communication line. The operation of the converter is based on the use of the piezo-optic effect, which is dependent on mechanical voltage, depending on the DUIN01CH). The main reasons for the change in the sensitivity of a piezo optic transducer is the dependence on the light output of the LED (C) and the sensitivity of the photodiode (K). It can be shown that the sensitivity of the transmitter is pro-ionic, which is on the photodiode sensitivity of the photodiode. Neglect of a relatively small dark current {3f, we can assume that the initial m (photodiode (G) is also suitable for these values. Therefore, maintaining a constant value of the initial current of the photodiode 1yr to preserve the constant sensitivity. The optical system described allows for loading the sensitive element 3, to obtain an increment of the photodetector's lightness of the same magnitude and contrasts with the sound.With linear deluxe 4mper characteristics of the photoreceivers 7 and 8 and the same the initial current (tJ), the sum of the photodetection currents of the LPS, and hence, and the junction on the resistor 13 does not depend on the measured force Р С + Sfjit o). When changing, for example, as the temperature increases, the light output of the LED drops, the luminous flux decreases and, as a result, the currents of the photodiodes 7 and 8 decrease. The voltage drop across the common resistor 13 decreases, the output of the comparator unit 14 appears to the input of the controlled power supply 16, which increases the voltage of the power supply of the LED 1. Therefore, its luminous flux increases, thereby increasing the currents of the photodiodes 7 and 8 and the voltage across the resistor 13, tending to its original value. For a smooth adjustment of the sensitivity of the piezo optic converter, the resistor 13 can be made variable. In addition to maintaining feedback, it is desirable to include a thermistor 17 or a resistor in the power supply circuit of the LED. This partial autothermal compensation facilitates the requirements of the scheme described above or, ceteris paribus, reduces the temperature dependence of the sensitive transducer. The formula of the invention. A piezo-optical measuring transducer containing a light source, a polarization-optical system and two differentially connected photodetectors, characterized in that, in order to improve accuracy by reducing the dependence of the sensitivity of the converter on temperature, it is equipped with a reference voltage source controlled by the light source power supply. , the comparison unit and the output signal adder of the photodetectors connected to one of the inputs of the comparison unit, the other input which is connected the source of the reference voltage, and the output to the input of the controlled power supply unit.