Предлагаемый прибор, назначаемый дл определени размеров издели с учетом допускаемых в них отступлений, имеет вид раздвижнога калибра или штангенциркул , подвижна губка которого выполнена поворотной вокруг установленной на движ1:е оси и снабжена стрелой дХй отсчета на шкале отклонений фактического размера от номинального.The proposed device, assigned to determine the dimensions of the product with allowance for the deviations allowed in them, has the form of an expanding gauge or vernier caliper, the movable sponge of which is rotatable around the axis installed on the slide: e and is equipped with a dHi boom on the scale of deviations of the actual size from the nominal one.
На чертеже фиг. 1 изображает общий вид прибора спереди; фиг. 2 - вид сбоку движка; фиг. 3-такой же вид неподвижной губки, и фиг. 4--вид сверху концевой защелки.In FIG. 1 shows a general view of the device from the front; FIG. 2 - side view of the engine; FIG. 3 is the same kind of fixed jaw; and FIG. 4 is a top view of the end latch.
По линейке 7 с делени ми на задней стороне и с закрепленной на конце неподвижной губкой 2 может переставл тьс плотно охватывающий линейку движок 3, несущий на оси 9 подвижную губку 4 в виде подпружиненного двухконечного поворотного рычага со стрелкой 5 к дуговой шкале 7. Обе губки снабжены кажда двум упорами 8, из которых нижние служат дл измерени изделий снаружи, а верхние-дл измерени изнутри отверстий и т. п. Дл более точной установки на линейке 7 движка 3 имеетс еще дополнительный движок 75, св занный с пер327The ruler 7, with divisions on the back side and with a fixed sponge 2 fixed at the end, can be rearranged by the slider 3 tightly spanning the ruler, carrying on the axis 9 the movable sponge 4 in the form of a spring-loaded two-pointed rotary lever with an arrow 5 to the arc scale 7. Both jaws are equipped with each with two stops 8, of which the lower ones are used to measure products from the outside, and the upper ones are for measuring inside holes, etc. For a more precise installation on slider 7 slider 3 there is also an additional slider 75 associated with the first 327
вым при помощи микрометренного винта 74. На шурупах 10, которыми закреплена на линейке 7 губка 2, могут, как на ос х, поворачиватьс еще две линейки 6, проход щие , так же, как и линейка 7, через соответственные прорезы в обоих движках и зажимаемые на конце линейки 7 защелкой 73. На оси 9 губки 4 свободно надеты сзади стрелки 5 поворотные указатели J6 допусков, в виде стрелок с загнутыми вперед на шкалу 7 концами; отростки 77 этих указателей несут ролики 77, скольз щие при перемещении движка по ребрам линеек 6.with a micrometer screw 74. On the screws 10 that fix the sponge 2 on the ruler 7, you can, as on the axles, rotate two more ruler 6, passing, like the ruler 7, through the corresponding cuts in both slides and clamped at the end of the ruler 7 by the latch 73. On the axis 9 of the jaw 4, the rotary indicators J6 of tolerances are put on the rear arrows 5, in the form of arrows with 7 ends bent forward on the scale; the shoots 77 of these indicators are carried by the rollers 77, which slide as the slider moves along the edges of the rulers 6.
Пользуютс приспособлением следующим образом. Прежде всего линейки 6,6, поворотом их на ос х 70, устанавливаютс на известный допуск в размере издели , дл чего на конце линейки 7 имеютс делени , показывающие допуск в процентах, и закрепл ютс в этом положении защелкой 73. В соответствии с этим .автоматически установ тс указатели 76 и будут на шкале 7 указывать пределы допуска. Далее переставл ют движок 3 от руки и, более точно, - винтом 74 так, чтобы нулевое деление имеющегос на двнжке нониуса совпадало с делением на заднейUse the device as follows. First of all, rulers 6,6, by turning them on axes 70, are set to a known tolerance in the size of the product, for which, at the end of ruler 7, there are divisions showing the tolerance in percent and fixed in this position by latch 73. Accordingly. pointers 76 are automatically set and will indicate on the scale 7 the tolerance limits. Next, the engine 3 is rearranged by hand and, more precisely, by a screw 74 so that the zero division of the nonius on the nonius coincides with the division on the back