Лерка поворотно установлена в корj xe приспособлени , снабженного упором , по которому устанавливаетс угломер , состо щий из ножки и поворотной линейки.The turner is pivotally mounted in the core of the fixture, provided with an abutment against which the protractor is installed, consisting of a leg and a swivel ruler.
На чертеже фиг. 1 изображает вид приспособлени спереди; фиг. 2-разрез ио линии АВ на фиг. 1; фиг. 3 - вид спереди ножки угломера; фиг. 4 - вид сбоку с частичным разрезом; фиг. 5 - вид линейки угломера спереди; фиг. 6 -- вид линейки сверху.In FIG. 1 is a front view of the device; FIG. 2-section of the line AB in FIG. one; FIG. 3 is a front view of the protractor leg; FIG. 4 is a side view with a partial cut; FIG. 5 is a front view of the protractor ruler; FIG. 6 - top view of the ruler.
Приспособление состоит из корпуса / с привинченным к нему винтами кольцом 2. В корпусе находитс обойма 3 со сменной втулкой 4. Угломер опираетс на планку 8. Обойма 3 со сменной втулкой 4 и вложенной в последнюю плашкой может вращатьс в корпусе J. Рабочее положение обоймы 3 фиксируетс винтами 77. Плашка закрепл етс во втулке 4, сменной в зависимости от размера плашек, боковыми винтами, а винтом ТО втулка скрепл етс с обоймой 3, Угломер может смещатьс по упору 8 в сторону на требуемое рассто ние. При этом положение встри а ножки 5 угломера не измен етс относительно центровой линик плашки. Положение угломера фиксируетс винтами J3. Дл поворота линейки б угломера вокруг остри а на линейке сделан выступ Ь с зубцами 75-75, вход щими в выфрезерованный Т-рбразный дуговой паз на ножке 5. На линейке 6 нанесены угловые делени от 0° до 15°. Закрепление линейки производитс установочной планкой 7 и винтом 72.The device consists of a body / with a ring 2 screwed to it. The case contains a sleeve 3 with a replaceable sleeve 4. The protractor rests on the bar 8. The sleeve 3 with a replaceable sleeve 4 and inserted into the last plate can rotate in the case J. The working position of the sleeve 3 is fixed by screws 77. The plate is fixed in sleeve 4, interchangeable depending on the size of the dies, side screws, and screw THEN the sleeve is attached to the holder 3, the protractor can be displaced along the stop 8 to the side by the required distance. At the same time, the position of the spacer legs 5 of the protractor does not change relative to the center line of the plate. The position of the protractor is fixed with screws J3. To rotate the ruler b of the protractor around the point, a ruler b is made on the ruler with teeth 75-75 that enter the milled T-tongue arc groove on the leg 5. On the ruler 6 there are angular divisions from 0 ° to 15 °. The ruler is secured by an adjustment bar 7 and a screw 72.
Угломер смещают в сторону е таким расчетом, чтобы острие а ножки совпало с вершиной угла сектора плашки, а затем устанавливают линейку на определенный угол, закрепл ют ее и производ т запиловку под этот угол. После этого освобождают винты 77 и поворачивают обойму с плашкой на соответствующий угол, в зависимости от количества секторов. В этом новом положеНИИ плашку снова закрепл ют и запиливают следу1рщий сектор. Дл повышени точности запиловки, а также и дл использовани приспособлени , как контрольного прибора, на корпусе и обойме нанос тс углы, поворота в зависимости, от числа секторов.The protractor is shifted to the side e in such a way that the tip of the legs coincides with the top of the corner of the die sector, and then set the ruler at a certain angle, fix it and cut it to this angle. After that, loose the screws 77 and rotate the clip with the plate to the appropriate angle, depending on the number of sectors. In this new position, the plate is again secured and washed down the next sector. In order to improve the accuracy of the seaming, as well as to use the device as a control device, angles, rotation depending on the number of sectors, are applied to the housing and the yoke.
Предмет изобретени .The subject matter of the invention.