Известны двойные торцовые уплотнени дл валов центробежных насосов, состо щие из двух невращающихс втулок и двух контактирующих с ними вращающихс втулок, нагруженных в осевом направлении действием пружины и давлением уплотн ющей жидкости. Однако такие уплотнени мало пригодны дл валов насосов, работающих на повыщенных давлени х, вследствие высоких удельных давлений, возникающих на контактирующих торцовых поверхност х втулок.Double mechanical seals are known for the shafts of centrifugal pumps, consisting of two non-rotating sleeves and two rotating sleeves in contact with them, loaded in the axial direction by the action of a spring and the pressure of a sealing fluid. However, such seals are not very suitable for pump shafts operating at increased pressures due to the high specific pressures arising on the contacting end surfaces of the sleeves.
С целью разгрузки вращающихс втулок от давлени уплотн ющей жидкости в предлагаемом торцовом уплотнении применена гильза, один конец которой воспринимает своей торцовой поверхностью атмосферное давление.In order to unload the rotating sleeves from the pressure of the sealing fluid, in the proposed mechanical seal, a sleeve is used, one end of which perceives atmospheric pressure with its end surface.
На чертеже изображено оиисываемое уплотнение в разрезе.The drawing shows the designed seal in the section.
Уплотнение состоит из двух невращающихс втулок / и 2 и двух контактирующих с ними вращающихс втулок 3 и 4. Втулка 4 жестко соединена с гильзой 5, левый конец которой (меньшего диаметра) вставлен в расточку втулки 3 и подвижно сочленен с ней посредством БИНТОВ 5 и 7 И щлицевой втулки 8. Дл обеспечени вращени втулок 3 и 4 гильза 5 соединена винтом 9 с обоймой 10, укрепленной на валу //. Гильза 5 снабжена внутренней расточкой, в которой установлены две манжеты 12 и 13, нагруженные действием пружины М и давлением уплотн ющей жидкости, подводимой через отверстие 15. Применение манжет 12 и 13 исключает возможность прорыва перекачиваемой насосом жидкости вдоль обоймы 10 и позвол ет подвести к торцовым поверхност м левого конца гильзы 5 и расточки втулки 5 атмосферное давление.The seal consists of two non-rotating sleeves / and 2 and two rotating sleeves 3 and 4 in contact with them. Sleeve 4 is rigidly connected to sleeve 5, the left end of which (of smaller diameter) is inserted into the bore of sleeve 3 and is movably connected to it by means of BINT 5 and 7 And slotted sleeve 8. To ensure the rotation of the sleeves 3 and 4, the sleeve 5 is connected by a screw 9 with the holder 10, mounted on the shaft //. The sleeve 5 is provided with an internal bore in which two cuffs 12 and 13 are installed, loaded by the action of the spring M and the pressure of the sealing fluid supplied through the opening 15. The use of the cuffs 12 and 13 excludes the possibility of a breakthrough of the pumped fluid along the sleeve 10 and allows the surfaces of the left end of the sleeve 5 and the bore of the sleeve 5 are atmospheric pressure.
При диаметре расточки втулки 3, равном диаметру ее контактирующей части, действие уплотн ющей л идкости, поступающей через канал 16, на обе вращающиес втулки 3 и 4 будет уравновешено. В этом случае втулки 3 н 4 будут находитьс только под воздействием пружины 17.With the diameter of the bore of the sleeve 3, equal to the diameter of its contacting part, the effect of the sealing fluid entering through the channel 16 on both rotating sleeves 3 and 4 will be balanced. In this case, the sleeves 3 and 4 will be only under the influence of the spring 17.