Przedmiotem wzoru użytkowego jest miska ustępowa spłukiwana wodą z bezobrzeżową muszlą klozetową (1), z doprowadzeniem wody spłukującej w górnej, tylnej jej części, obejmującym rurę wlotową (8) kończącą się otworem wlotowym (7) oraz umieszczony za nim kanał (9) kończący się ujściem (10). Otwór wylotowy (2) do syfonu jest umieszczony w dolnej części muszli (1). Miska ustępowa ma pierwszą płaszczyznę środkową, w stanie zmontowanym miski równoległą do ściany montażowej i dzielącą miskę myślowo przez środek otworu wylotowego (2) na część przednią i tylną, oraz prostopadłą do niej drugą płaszczyznę środkową, dzielącą miskę przez środek otworu wylotowego (2) na część prawą i lewą. Muszla klozetowa (1) posiada górną krawędź (6), stanowiącą fragment górnej, wewnętrznej powierzchni muszli (1) znajdujący się bezpośrednio poniżej osłony zewnętrznej, o kształcie w przybliżeniu eliptycznym, utworzoną w formie płaskiego pierścienia o zasadniczo pionowych ścianach. Otwór wylotowy (2) jest przesunięty w obrębie tej elipsy w stronę tyłu miski ustępowej. Ujście (10) kanału (9) umieszczone jest niesymetrycznie względem drugiej płaszczyzny środkowej, z prawej lub lewej strony muszli (1) w jej górnym obszarze, tak, że woda spłukująca napływa do niej padając w pierwszej kolejności na tylną część górnej krawędzi (6), w kierunku zasadniczo poziomym i stycznym do wewnętrznej powierzchni muszli (1), a następnie wykonuje wewnątrz niej ruch obrotowy. Miska ustępowa charakteryzuje się tym, że wewnętrzny kształt muszli klozetowej (1), pomijając położenie ujścia (10), ma symetryczny kształt względem drugiej płaszczyzny środkowej, i tym, że muszla (1) po swojej wewnętrznej stronie, na wysokości ujścia (10) i tuż poniżej górnej krawędzi (6), posiada próg górny (12) utworzony w formie wybrzuszenia przebiegającego horyzontalnie dookoła wewnętrznej powierzchni muszli klozetowej (1), przy czym w tylnym obszarze muszli klozetowej (1) jest on nieco mniej wystający niż w innych jej obszarach.The object of the utility model is a flushable toilet bowl with a rimless toilet bowl (1), with a flushing water supply in its upper, rear part, including an inlet pipe (8) ending with an inlet opening (7) and a channel (9) located behind it, ending the outlet (10). The outlet (2) for the siphon is located in the lower part of the bowl (1). The toilet bowl has a first central plane, in the assembled state of the bowl, parallel to the assembly wall and dividing the bowl by thought through the center of the outlet opening (2) into the front and rear parts, and a second middle plane perpendicular to it, dividing the bowl by the center of the outlet opening (2) into right and left part. The toilet bowl (1) has an upper edge (6), which is a part of the upper, inner surface of the bowl (1) directly below the outer casing, approximately elliptical in shape, formed in the form of a flat ring with essentially vertical walls. The outlet opening (2) is shifted within this ellipse towards the rear of the toilet bowl. The mouth (10) of the channel (9) is placed asymmetrically with respect to the second median plane, on the right or left side of the shell (1) in its upper area, so that the flushing water flows into it, falling first on the rear part of the upper edge (6) in a substantially horizontal direction and tangential to the inner surface of the shell (1) and then rotates therein. The toilet bowl is characterized by the fact that the internal shape of the toilet bowl (1), apart from the position of the mouth (10), has a symmetrical shape with respect to the second median plane, and that the bowl (1) on its inner side, at the level of the mouth (10) and just below the upper edge (6), it has an upper ridge (12) formed in the form of a bulge running horizontally around the inner surface of the toilet bowl (1), and it is slightly less protruding in the rear region of the toilet bowl (1) than in other areas.