Der Gegenstand der Erfindung ist eine Haarschneidemaschine, die von
einem Magnet über einen frei schwingenden Anker mit Hebelübersetzung angetrieben
wird.The subject of the invention is a hair clipper made by
a magnet driven by a freely oscillating armature with leverage
will.
Haarschneidemaschinen sind in verschiedenen Ausführungen bekannt.
Sie bestehen aus einem Elektromotor, der über ein Untersetzungsgetriebe, meist Schneckenantrieb
und Kurbel, die für das Haarschneiden notwendige Hinundherbewegung erzeugt. Dabei
wird der Motor klein gehalten, damit er im Handgriff untergebracht werden kann,
was eine gewisse Präzision und Kompliziertheit mit sich bringt.Hair clippers are known in various designs.
They consist of an electric motor, which is driven by a reduction gear, usually worm gear
and crank, which generates the reciprocating motion necessary for hair cutting. Included
the motor is kept small so that it can be accommodated in the handle,
which brings a certain precision and complexity with it.
Die Erfindung beruht nur auf dem Antrieb mittels Magnets. Zugmagnete
allgemeiner Art erhalten eine erhöhte Zugkraft mit dem gegenseitigen Näherkommen
der Pole, was eine ruckartige Bewegung hervorruft und ein geräuschvolles schlagartiges
Arbeiten bewirkt. Deshalb kommt hier eine Art Magnet zur Anwendung, bei der gemäß
Abb. I und 2 der Anker I an den Magnetpolen 2 vorbeigezogen wird. Entsprechend der
Ausbildung der Kurvenform 3 kann der Zugkraftverlauf nach den vorliegenden Verhältnissen
erhalten werden. Danach ist es möglich, die Kurvenform 3 so zu wählen, daß die Zugkraft
gleichmäßig ansteigt und wieder abfällt, so daß der Anker sich frei über die Pole
bewegt, ohne irgendwo aufzutreffen.The invention is based only on the drive by means of a magnet. Pull magnets
of a general nature receive an increased pulling force as they come closer to each other
the pole, which causes a jerky movement and a noisy sudden movement
Working causes. Therefore, a kind of magnet is used here, according to
Fig. I and 2 the armature I is pulled past the magnetic pole 2. According to the
Formation of the curve shape 3 can be the course of the tensile force according to the prevailing conditions
can be obtained. Then it is possible to choose the curve shape 3 so that the tensile force
rises and falls evenly, so that the armature moves freely over the poles
moves without hitting anywhere.
Abb. 3 stellt nun diese neue Haarschneidemaschine schematisch dar.
Die äußere Form paßt sich den bisherigen Haarschneidemaschinen an, und der Magnetantrieb
ist im Handgriff untergebracht. Die Magnetart nach Abb. I ist hier doppelt wirkend
vorhanden, so daß der Anker I abwechselnd hin und her gezogen wird. Die Magnetspulen
erhalten von einem Umschalter (Kippschalter) 4, der vom Ankerhebel 5 gesteuert wird,
abwechselnd Strom. Damit die Ankerbewegung rhythmisch und gleichschwingend verläuft,
sind zwei Pufferfedern 5 angebracht, die die Ankerbewegung einerseits abbremsen
und andererseits in der umgekehrten Richtung beschleunigen. Um die gewünschte Schwingungszahl
einstellen zu können, ist auf dem Ankerhebel 5 ein verstellbares Gewicht 7 angebracht,
da sich die Schwingungsfrequenz des Ankerhebels nach dessen Schwungmasse richtet.
Mit 8 ist der Drehpunkt des Ankerhebels 5 bezeichnet. Der weitere Teil des Ankerhebels
stellt den Bewegungszapfen 9 für das Aufstecken des Schneideinsatzes Io dar. Da
am Bewegungszapfen 9 nur ein kurzer Weg gebraucht wird, kann der Magnet entsprechend
dem Hebelverhältnis a : b klein gehalten werden. Abb. 4 zeigt in bildlicher Darstellung
eine andere Form des Magnets, bei dem eine etwas größere Kraftwirkung zu erwarten
ist. Die Arbeitsweise entspricht der in Abb. 3.Fig. 3 now shows this new hair clipper schematically.
The outer shape adapts to the previous hair clippers, and the magnetic drive
is housed in the handle. The type of magnet according to Fig. I is double-acting here
present, so that the anchor I is alternately pulled back and forth. The solenoids
obtained from a changeover switch (toggle switch) 4, which is controlled by the armature lever 5,
alternating electricity. So that the anchor movement is rhythmic and oscillating,
two buffer springs 5 are attached, which on the one hand brake the armature movement
and on the other hand accelerate in the opposite direction. To the desired number of vibrations
to be able to adjust, an adjustable weight 7 is attached to the armature lever 5,
because the oscillation frequency of the armature lever depends on its flywheel.
The fulcrum of the armature lever 5 is denoted by 8. The other part of the anchor lever
represents the movement pin 9 for attaching the cutting insert Io. Da
only a short way is needed on the movement pin 9, the magnet can accordingly
the leverage ratio a: b can be kept small. Fig. 4 shows in a pictorial representation
another form of magnet, where a slightly larger force can be expected
is. The mode of operation corresponds to that in Fig. 3.
Eine rhythmische Schwingbewegung kann auch erzielt werden, wenn der
Magnet nur in einer Richtung wirkt und die Rückbewegung durch eine Feder II (Abb.
5) verursacht wird. Hier liegt die Magnetanordnung nach Abb. 2 vor. Entsprechend
stellt dies Abb. 6 mit zwei solchen Magneten doppelt wirkend dar.A rhythmic swinging movement can also be achieved when the
The magnet only works in one direction and the return movement is controlled by a spring II (Fig.
5) is caused. Here is the magnet arrangement according to Fig. 2. Corresponding
Fig. 6 shows this with two such magnets double-acting.
Der Schalter kann nun nach Abb. 7 vom Ankerhebel 5 aus zwangsläufig
über den Kippkontakt I2 abwechselnd auf die Kontakte I3 gesteuert werden, oder aber
es wird ein Verbindungsglied in Form von Feder I4 verwendet, wobei dann ein Kippschalter
nach Abb. 8 vorliegt.The switch can now inevitably from the armature lever 5 as shown in Fig. 7
alternately controlled via the toggle contact I2 to the contacts I3, or else
a connector in the form of spring I4 is used, then a toggle switch
according to Fig. 8 is available.
Abb. 9 zeigt die äußere Form dieser Haarschneidemaschine, die auch
rund oder oval sein kann; der bequemsten Handhabung angepaßt.Fig. 9 shows the external shape of this hair clipper, which too
can be round or oval; adapted to the most comfortable handling.