Es ist bereits vorgeschlagen worden, zum An. trieb von Plattenspielern
und ähnlichen Geräten Einphaseninduktionsmotoren zu verwenden, an deren Hauptpolen
Hilfspole vorgesehen sind, die von einer kurz geschlossenen Wicklung bzw. nur einem
Kurzschlußbügel umschlungen werden.It has already been suggested to be an. drifted from turntables
and similar devices to use single-phase induction motors at their main poles
Auxiliary poles are provided by a short-circuited winding or only one
Short-circuit hoops are wrapped.
Das von den Hauptpolen ausgehende Wechselfeld bringt bekanntlich in
den Hilfspolen ein um 9o° phasenverschobenes Hilfsfeld hervor. Das primäre und das
induzierte Feld setzen sich zu einem elliptischen Feld zusammen; ohne dieses würde
der Motor nicht selbsttätig anlaufen.As is well known, the alternating field emanating from the main poles brings in
an auxiliary field phase-shifted by 90 ° emerges from the auxiliary poles. The primary and that
induced fields combine to form an elliptical field; without this would
the motor does not start by itself.
Phasenlage und Stärke der Hilfspole, deren Fluß durch die Kurzschlußbügel
verläuft, sind eng mit der in den Kurzschlußbügeln vernichteten Leistung verknüpft,
derart, daß das Anlaufmoment um so stärker wird, je mehr Leistung von den Kurzschlußbügeln
aufgenommen wird. Bei Motoren mit einem beträchtlichen Anlaufmoment tragen die Kurzschlußbügel
wesentlich zur Erwärmung des ganzen Motors bei. Die in ihnen erzeugte Verlustwärme
muß über das rückwärtige Ständerpaket an die Umgebung abgeleitet werden, so daß
das Ständerpaket eine hohe Temperatur annimmt, mit der auch die Wicklung belastet
wird. Es ist deshalb üblich, die Ankerachse mit einem Windflügel zu versehen, der
einen über das Ständerpaket streichenden Luftstrom erzeugt. Diese Kühlung ist aber
unvollkommen, und lokale Wärmestauungen können nicht vermieden werden. Außerdem
vergrößert ein Kühlflügel die Abmessung des Motors beträchtlich, insbesondere wenn
er den ganzen Motor kühlen muß.Phasing and strength of the auxiliary poles, their flux through the short-circuit bar
are closely linked to the power destroyed in the short-circuit bars,
in such a way that the starting torque becomes stronger, the more power from the short-circuit bars
is recorded. In motors with a considerable starting torque, the short-circuit bars wear
significantly contributes to the heating of the entire engine. The heat loss generated in them
must be discharged to the environment via the rear stator package, so that
the stator package assumes a high temperature, which also loads the winding
will. It is therefore common to provide the anchor axle with a wind vane, which
generates an air flow sweeping over the stator package. This cooling is however
imperfect and local heat build-up cannot be avoided. aside from that
a cooling wing increases the size of the engine considerably, especially when
he has to cool the whole engine.
Nach der Erfindung wird dadurch Abhilfe geschaffen, daß unmittelbar
dort, wo die Verlustwärme entsteht, nämlich an den Kurzschlußbügeln, Kühlbleche
angeordnet werden, die in den von einem kleinen rotierenden Windflügel erzeugten,
räumlich begrenzten Luftstrom hineinragen, so daß die entstehende Wärme zum größten
Teil von den Kurzschlußbügeln abgeführt wird, noch ehe sie auf andere Teile des
Motors übertragen wurde. Sie bestehen vorteilhaft aus einem Werkstoff guter Wärmeleitfähigkeit.
Am zweckmäßigsten wird ein Teil des Kurzschlußbügels als Kühlblech ausgebildet.
Bei einem Motor nach der Erfindung, wie er in der Abbildung in einem Ausführungsbeispiel
dargestellt ist und im folgenden beschrieben wird, kommt man mit einem so kleinen
Windflügel aus, daß seine Abmessungen praktisch kaum vergrößert werden. Die Wirkung
läßt sich noch weiterhin verbessern durch Anordnung einer wärmeisolierenden Schicht
zwischen Kurzschlußbügel und Ständerpaket.According to the invention, a remedy is provided that immediately
where the heat loss occurs, namely on the short-circuit bars, cooling plates
placed in the generated by a small rotating wind vane,
Spatially limited air flow protrude, so that the heat generated to the greatest
Part of the short-circuit clips is discharged before they can be transferred to other parts of the
Engine was transferred. They advantageously consist of a material with good thermal conductivity.
Most expediently, part of the short-circuit clip is designed as a cooling plate.
In a motor according to the invention, as shown in the figure in an exemplary embodiment
is shown and is described below, you come up with such a small one
Wind blades from that its dimensions are practically hardly increased. The effect
can be further improved by arranging a heat insulating layer
between short-circuit bar and stator package.
Fig. i# zeigt einen Einpbaseninduktionsmotor in Seitenansicht, Fig.
2 in Draufsicht, zum Teil im Schnitt längs der Linie I-1.Fig. I # shows a single-phase induction motor in side view, Fig.
2 in plan view, partly in section along line I-1.
Auf dem Ständerpaket i ist die Wicklung 2 angeordnet. Die Hilfspole
tragen eine kurzgeschlossene Wicklung bzw. nur einen einzigen Kurzschlußbügel 4.
Unmittelbar an diesen sind Kühlbleche 5 vorgesehen, die die Wärme ableiten und an
den Luftstrom abgeben, der von dem auf der Ankerwelle 6 sitzenden Windflügel 7 erzeugt
wird. Die Kühlbleche sind einfach abgewinkelte Bleche, mit den offenen kupfernen
Kurzschlußbügeln durch Lötung verbunden und bilden mit ihnen einen geschlossenen
Stromkreis.The winding 2 is arranged on the stator package i. The auxiliary poles
carry a short-circuited winding or only a single short-circuit clip 4.
Immediately on these cooling plates 5 are provided, which dissipate the heat and to
give off the air flow generated by the wind blade 7 sitting on the armature shaft 6
will. The cooling sheets are simply angled sheets, with the open copper ones
Short-circuit bars connected by soldering and form a closed one with them
Circuit.