Claims (5)
Beschreibung: Bei der Feuerung handelt es sieh. um. ein Gelenk für Standleuehten im folgenden kurz, G-elenk, bezeichnet. Es gibt zwar schon einige Gelenke dieser Art aus Metall. Dieses Gelenke haben aber alle den !"achteil, daß sie sich nur begrenzt bewegen lassen. Das neue G-elenk weißt äiese Fachteile nicht auf und läßt sieh fast um 350° bewegen. Hierdurch ist es möglich Standleuehten mit einem sehr großem Wirkungsgrad zu bauen. Die leuerung wird Beispielsweise dargestellt durch Abbildung 1) Aufsicht. Abbildung 2) Aufsieht im Schnitt Abbildung 3) Kappe A seitliche Sicht Abbildung 4) Kappe B seitliehe Sicht Die Feuerung ist vorzugsweise aus Kunststoff gefertigt, es können aber auch andere Materialien benutzt werden, zum Beispiel: Metall oder ähnliches. Die Feuerung besteht aus der Kappe A + B, der Schraube C, des Knebels D, des Seegerings K und der beiden Schrauben G-. Kappe A + B haben ein seitliches Loch D in das das Standrohr, baw. das Rohr an dem der leuchtenschirm befestigt ist, eingesteckt werden, Die Rohre werden durch die Sehrauben G- festgesetzt. Dabei ragt wenigstens eine der beiden Schrauben mit ihrem Kopf über den Rand des Schraubloches hinaus. Die Schraube 0 hat unter ihrem Kopf einen Yierkant (I) von wenigen Millimetern . Die Kappe B hat eine vierkantige Bohrung H. In diese Bohrung H ist die Schraube C so eingeführt, daß sie sich nicht drehen hann. ( Durch eckige Bohrung H und dem Yierkant I unter dem Schraubenkopf.) Die Kappe A ist so auf die Schraube C aufgesetzt, daß die offene Seite von Schale Ä auf der offenen Seite von Kappe B liegt. Durch den Seegering K auf Schraube 0 werden die Kappe A und B zusammengehalten. Durch Aufschrauben des Knebels D auf Schraube C wird A + B ( je nach anziehen des Knebels D ) mehr oder weniger aufeinander gedruckt. Durch das, mehr oder weniger, Anziehen des Knebels D läßt sich die Bewegungsgängi^keit von Schale A über Schale B genau regulieren. Mindestens einer der Köpfe der Schrauben G die in die Kappe hineinragen verhindert durch anschlagen, daß man Kappe A + B mehr als um 350° gegeneinander verdrehen kann. SchutzansprücheDescription: The firing is about. around. a joint for standing people in the following for short, G-elenk, referred to. There are already some joints of this type made of metal. These joints all have the disadvantage that they can only be moved to a limited extent. The new G joint does not have these specialist parts and can be moved by almost 350 °. This makes it possible to build standing lights with a very high degree of efficiency. The control is shown for example by Figure 1) Top view Figure 2) View in section Figure 3) Cap A side view Figure 4) Cap B side view The furnace is preferably made of plastic, but other materials can also be used, for example : Metal or similar. The furnace consists of the cap A + B, the screw C, the toggle D, the circlip K and the two screws G. Cap A + B have a side hole D in which the standpipe, baw The tube to which the lampshade is fastened can be inserted, the tubes are fixed by the screw holes G. At least one of the two screws protrudes with its head over the edge of the screw hole e screw 0 has a square head (I) of a few millimeters under its head. The cap B has a square hole H. The screw C is inserted into this hole H so that it cannot turn. (Through the angular hole H and the Yierkant I under the screw head.) The cap A is placed on the screw C in such a way that the open side of shell Ä lies on the open side of cap B. Cap A and B are held together by the circlip K on screw 0. By screwing the toggle D onto screw C, A + B (depending on how tightly the toggle D is tightened) is printed more or less on top of each other. By, more or less, tightening the toggle D, the movement from shell A to shell B can be precisely regulated. At least one of the heads of the screws G that protrude into the cap prevents by striking that cap A + B can be turned more than 350 ° against each other. Protection claims
1.) Stadleuchtengelenke dadurch gekennzeichnet, daß es vorzugsweise aus Kunststoff gefertigt ist.
1.) City light joints, characterized in that it is preferably made of plastic.
2.) Standleuchtengelenk nach Anspruch 1; gekennzeichnet, durch je
ein Rohr i1, das in den Schalen A und B mit je einer Schraube G
befestigt ist.2.) floor lamp joint according to claim 1; characterized by a tube i 1 , which is fastened in the shells A and B with a screw G each.
3.) Gelenk nach Anspruch 1 und 2 gekennzeichnet durch eine Schraube G-die
über den Rand des Schraubloehes hinausragt.3.) Joint according to claim 1 and 2 characterized by a screw G-die
protrudes over the edge of the screw hole.
4.) Gelenk nach Anspruch 1;2;3? gekennzeichnet durch die, unter ihrem
Kopf vierkantig (I) ausgebildeter Sehraube C.4.) Joint according to claim 1; 2; 3? characterized by the, under her
Head square (I) formed visual hood C.
5.1 Gelenk nach Anspruch 152;3;4; gekennzeichnet durch einen auf
die Schraube-G aufgesteckten Seegering D, zum zusammenhalten der Schalen A +B.5.1 Joint according to claim 152; 3; 4; marked by an on
the screw-G attached circlip D to hold the shells A + B together.