Griffstück für Armaturen.Handle for fittings.
Die Erfindung bezieht sich auf solche Griffstücke von Sanita*armaturen,
die auf dem Spindelende mit einer zentralen, eingesenkten Stiftschraube befestigt
werden, und bezweckt eine leicht wechselbar, den hygienischen und geschmacklichen
Anforderungen gerecht werdende Kaschierung des zur Unterbringung des Stiftschraubenkopfes
dienenden Senkloches im Griffstück. The invention relates to such handles of Sanita * fittings,
which is attached to the end of the spindle with a central, countersunk stud screw
and aims to be easily changeable, hygienic and tasty
Covering that meets the requirements for accommodating the stud screw head
serving sinkhole in the handle.
Für diese Griffbefestigung ist bekannt die Kaschierung mit einem
Svhraubplättchen vorzüglich aus Kunststoff. Zur Vermeidung der teuren und den zugang
von Feuchtigkeit fördernden Schraubgänge ist ferner bekannt, das Senkloch im Griffstück
zu unterscheiden und ein genau gepasstes, ebenes Kunststoffplättchen einzudrücken,
welches vermöge der Unterschneidung druckknopfartig sitzenbleibt. For this handle attachment, the lamination with a is known
Svhraubplätchen especially made of plastic. To avoid the expensive and the access
of moisture-promoting screw threads is also known, the countersunk hole in the handle
to distinguish and to press in a precisely fitted, flat plastic plate,
which by virtue of the undercut remains in place like a push button.
Der Nachteil dieser Ausführung, dass wegen der geringen Elastizität
des ebenen Plättchens die Masse bzw. Toleranzen sehr eng gehalten werden müssen,
damit ein scharfer, dichter Schluss eintritt, und dass eine Wiederabnahme des Plättchens
z. B. zur Vornahme einer Reparatur nur unter seiner Zerstörung erfolgen kann, wird
gemäss Erfindung dadurch in idealvollkommener Weise behoben, dass als druckknopfartig
in das unterschnittene Senk-
loch einzudrückender Kaschierungskorper eine Kappe mit Bund
verwendet wird, und der Bord dieser Bundkappe so geformt ist, z. B. konisch oder
mit einem der Unterschneidung des Senkloches entsprechend geformten Rastvorsprung,
dass die Kappe druckknopfartig federnd in der Unterschneidung des Senkloches ein-und
durch
Anheben unter dem Bund auch wieder ausrastbar ist.The disadvantage of this design is that because of the low elasticity of the flat plate, the mass or tolerances must be kept very tight so that a sharp, tight seal occurs, and that a removal of the plate z. B. to undertake a repair can only be done by destroying it, according to the invention is thus remedied in an ideally perfect way that as a push button in the undercut countersink The lamination body to be pressed in has a cap with a collar
is used, and the board of this collar cap is shaped, e.g. B. conical or with a locking projection corresponding to the undercut of the countersunk hole, so that the cap resiliently engages in the undercut of the countersunk hole like a push button and can also be disengaged again by lifting under the collar.
Die beigegebene Abbildung zeigt die Erfindung in grösserem Masstabe
beispielsweise bei einem Glockengriff 1, der mit der Stiftschraube 2 auf der Ventilspindel
3 gesichert ist 4 ist das Senkloch im Griffstück zur Aufnahme des Schraubenkopfes,
welches die Unterschneidung 5 hat. 6 ist dn. e Kappe, deren Bord 7 als Rastvorsprung
die Bauchung 8 hat, welche beim Eindrücken federnd in der Unterschneidung 5 bis
zum festen Anliegen des umlaufenden Bundes 9 einrastet, während etwa mittels Untergreifen
des Kappenbundes mit einem Messer die Kappe wieder Ausrast-und abnehmbar ist. The accompanying figure shows the invention on a larger scale
for example with a bell handle 1, the one with the stud 2 on the valve spindle
3 is secured 4 is the countersunk hole in the handle to accommodate the screw head,
which has the undercut 5. 6 is thin. e cap, the board 7 of which acts as a locking projection
has the bulge 8, which when pressed in resiliently in the undercut 5 to
to the firm application of the circumferential collar 9 engages, while about by means of reaching under
of the cap collar with a knife, the cap can be disengaged and removed again.
Der Fortschritt der Ausführung liegt, wie aus der Darstellung klar
ersichtlich', einerseits in der verstärkten Federung des rohrförmigen Kappenbordes,
die auch bei größeren Toleranzen einen dichten Abschluss und festen Sitz erzielt,
andererseits in der leichten, zerstörungsfreien Entfernung, und endlich in einer
bedeutenden Verbesserung von Hygiene und geschmacklichen Aussehen. The progress of the execution lies, as is clear from the representation
visible ', on the one hand in the reinforced suspension of the tubular cap brim,
which achieves a tight seal and a tight fit even with larger tolerances,
on the other hand in the easy, non-destructive removal, and finally in one
significant improvement in hygiene and taste-like appearance.
Es versteht sich, dass die Bundkappe vorzugsweise aus Kunststoff
besteht, der entsprechend dem Anwendungszweck-Heiss, Kalt----gefärbt ist. It goes without saying that the collar cap is preferably made of plastic
exists, which is colored according to the application - hot, cold ----.