"-, 8 C h r e i b a n g
igar Gebraucheausteraumeldung der Firma Kionka Co K Brian-
gen,NeumUhle 1 vom 28. 6. 60
tTretblock aus Kunststoff für Pahrrad- Kinderad-* tmd Mopeds
pedale*
Trotblöcke aus Xanststoff sind neben den allgemein benutzten
Blöcken ans eumai bereits bekannt. Diese TretblScke aus Kunst-
stoff'gleichen jedoch in ihrer Ausführung den Blöcken aus
Gummi und weisen daher nur eine höhere Abriebfestigkeit gegen-
über Gummi auf.
Die ! retb16cke der vorliegenden Gebrauchsmusteranmeldung sind
durch sinnvolle Kombination von Hohlräumen und Ab ; Btützstre-
ben in Inne= des Blockes aus einen themoplastischen Kunst-
Stoff so hersustellen, daß der Tretbloek eine Gitterkonstruk-
tion darstellt (Abb. 1y 3 und 4. Die Abstützungen können dabei
wahlweise längs oder senkrecht zu dem FUhrungsstift angebracht
werden. Es ergeben eich dann gegenüber den heute noch aberwie-
gend verwendeten gumipodelblöcken folgende Vorteilen
Das Gewicht des neuen Tretblockes aus Kunststoff
beträgt nur noch etwa ein Drittel
Der Material. maat. für den neuen Tretblock beträgt
nur noch etwa die Hälfte
Die Abriebfestigkeit der Haftfläehe des Tretbloekes
wird um mindestens das Vierfache erhöht
Daraus ergeben sich in der : Praxis für den Verbraucher eine
we-
sentlich längere Gebrauchsdauer des Blockes und damit ein hö-
hererGebrauchswert.
Oleichzeitig garantiert die vorliegende Konstruktion die glei-
che Stabilität und die gleiche Haftfähigkeit am Fa. ß wie die
Blöcke aus G=mi* wobei eine allgemeine Pederung und Elasti-
zität des Blockes ein ausgezeichnetes Anschmiegen des Blockes
an den Fuß bewirkt.
m&M2
Weiterhin gestattet es die vorliegende Konstruktion, die bei
gamiblöcken allgemein bekannten kunsparungen (a) an der Stirn-
seite gegen das Verdrehen des Blockes beizubehalten. ein Fen-
ster Ce) anzubringen, in den ein Rückstrahlkörper aufgenommen
werden kann, hoh$, dRsa Punkte (f einzbauen, die eine ein-
wandfreit Lage des Rückstrahlkörpere garantieren und gleich-
Meitig durch die federnde Wirkung einen zusätzlichen Schutz
ge-
genBruch den Rütlcatrahlkt$rpern gewähren., sowie zur Stoßeiche-
rang des RUckstrahlkSrpera einen Pensterrand (g) anzabrin-
gezLI «
Ux eine leichtere Montage der Pedalen zu erzielen, wurde die
? Ur=g für den Stiftp der den Tretblock mit dem pedalrahmen
verbindet, viereckig ausgefuhrt (b) 9 da die FHhrungastifte
an-
gelappt sind.
Wenn es Ausführung and Zweckmäßigkeit günstig erscheinen las-
sen, kann der teilweise freiliegende FBhrungastift zum Schatz
gegen Rost und Verschmutzung mit Kunststoff (c) umkleidet wer-
den oder auf der Rückseite oder den Stirnseiten wird ein Abdek-
kann (d) angebracht. die den Block geschlossen erscheinen läßt
und jtegliehe Verschmutzung verhindert,
um auf der Srittfläshe des Tretblockes aus Kunststoff die glei-
cheHaftfestigkeit wie bei Sümmi zn erzielen ist es erforder-
lich, daß statt der bisher bekannten rillenartigen Vertiefun-
gen eine inzahl kleiner erhabener Punkte angebracht wird (h,
die ein Abrutschen des Fußes nach jeder Seite verhindern.
"-, 8 cm
igar use deregistration notification of the company Kionka Co K Brian-
gen, NeumUhle 1 from June 28, 1960
tTread block made of plastic for bicycles, children, * tmd mopeds
pedals *
Trot blocks made of Xanst fabric are next to the commonly used ones
Blocks ans eumai already known. These pedal blocks made of synthetic
However, in terms of their design, the same material as the blocks
Rubber and therefore only have a higher abrasion resistance against
over rubber on.
The ! back of the present utility model application
through a sensible combination of cavities and ab; Btützstre-
practice inside = the block of a themoplastic art
Make fabric in such a way that the pedal block has a lattice structure
tion (Fig. 1y 3 and 4. The supports can
mounted either lengthways or perpendicular to the guide pin
will. I then give up to the still today
gumipodel blocks used have the following advantages
The weight of the new plastic pedal block
is only about a third
The material. maat. for the new pedal block
only about half
The abrasion resistance of the adhesive surface of the pedal block
is increased by at least four times
In practice, this results in a very important
significantly longer service life of the block and thus a higher
herer use value.
At the same time, the present construction guarantees the same
good stability and the same adhesion to Fa. ß as the
Blocks from G = mi * where a general pedestrian and elastic
city of the block an excellent nestling of the block
causes to the foot.
m & M2
Furthermore, it allows the present construction that at
Gamiblocks generally known cutouts (a) on the forehead
side to prevent the block from twisting. a fen
ster Ce) to be attached, in which a reflective body was added
can be built in high $, dRsa points (f, which have a
guarantee a wall-free position of the reflector body and
On the other hand, the resilient effect provides additional protection
Allow the vibrating beam to break, as well as to the butt oak
to attach a penster rim (g) to the retroreflective body.
gezLI «
Ux to achieve an easier assembly of the pedals, the
? Ur = g for the pin of the pedal block with the pedal frame
connects, square (b) 9 because the Fhrunga pins are
are lobed.
If execution and expediency seem favorable
sen, the partially exposed guide pin can be a treasure
clad with plastic (c) against rust and dirt
on or on the back or the front sides a cover
can (d) attached. which makes the block appear closed
and prevents any pollution,
to use the same plastic on the tread block
To achieve the same adhesive strength as with Sümmi zn it is necessary
that instead of the previously known groove-like indentations
a number of small raised points is attached (h,
which prevent the foot from slipping to either side.