Beschreibung zur Anmeldung des Helmut Ullmann Kaufbeuren - Neugablonz,
Neue Zeile 23.Description of the registration of Helmut Ullmann Kaufbeuren - Neugablonz,
New line 23.
Den Gegenstand für den beantragten Musterschutz bildet ein Manschettenknopf.A cufflink forms the subject of the applied for design protection.
Bei den bisher üblichen Manschettenknöpfen ist es von Nachteil, daß
der Steg, welcher durch die Knopflöcher der Hemdmanschette geschoben wird, fest
am Boden des Manschettenknopfes befestigt ist. Die dadurch bedingte"Dicke"des Manschettenknopfes
wirkt sich beim Auflegen des Unterarmes, insbesondere bei sitzenden Schreibarbeiten,
hinderlich aus, da man dann meist gerade den Arm auf dem Manschettenknopf liegen
hat. Um diese Wirkung, bezw. diese Behinderung zu verkleinern, wird verschiedentlich
der Steg nicht in einem
rechten Winkel an den Manschettenknopfboden befestigt9
sondernin einem schrägen Winkel von <sa 60 = 80. Be&
an-
derenManschettenknpfen wium wurde dieser Winkel durch
einen weiteren unsi. beibar hinter der Anbringung am Man-
sehettenknopfboden eingefügten Knick des Steges herbeige-
führt. Wurde jedoch der Knick, oder der Winkel, zu schräg angesetzt, so war dies
beim Einstecken des Nanschettenknop-
fes in die Manschette hinderlich. Beide Möglichkeiten sind
jedoch jeweils nur für etwas, und dies bis in die extremste
Ausführung, nützlich ; also der Steg im rechten Winkel beim
Einsteckenin die Hemdmanschette, und der möglichst schräge
Steg beim Tragen. Beide Möglichkeiten zu vereinigen war bei den bisher am Markt
befindlichen Modellen nicht möglich.In the case of the cufflinks that have been customary up to now, it is disadvantageous that the web, which is pushed through the buttonholes of the shirt cuff, is firmly attached to the bottom of the cufflink. The resulting "thickness" of the cufflink has an obstructive effect when the forearm is placed on, especially when writing while sitting, since one then usually has the arm resting on the cufflink. To this effect, respectively. To reduce this hindrance, sometimes the bridge is not rolled into one Attached to the bottom of the cufflink at right angles9
but at an inclined angle of <sa 60 = 80.
Their cufflinks wium this angle through
another unsi. beibar behind the attachment on the
sehettenknopfboden brought the bend of the bridge
leads. However, if the kink, or the angle, was set too diagonally, this was the case when the cuff link was inserted. fes in the cuff. Both options are
but only for one thing at a time, and this to the most extreme
Execution, useful; So the bridge at right angles
Put it in the shirt cuff, and if possible at an angle
Bridge when wearing. Combining both options was not possible with the models currently on the market.
Meine Ausgestaltung des Manschettenknopfsteges durch Einschaltung
eines drehbaren Lagers am Manschettenknopfboden behebt alle vorgenannten Mängel
leichteste Durch das Lager ist es möglich, den Manschettenknoppsteg in einem Winkel
von 1800 zu schwenken, wodurch jede gewünschte Stellung zu den gewünschteh Zeiten
vorhanden ist, und sich die jeweils praktischste und unauffälligste wie unaurtrãglichste
von ganz alleine einstellt. Dadurch kann man den Unterarm bei Schreibarbeiten ganz
b@om und ohne jede fühlbare Be-
hinderungauflegen, da der Mansehettenknopf die"Dicke"
verloren hat Beschädigungen des Scharniers sind in keinem
Falle zu erwarten, da die einzige Belastung in der Rieh-
Inng gehtg in welche der Steg dnrch die Drehbewegung nach
gibt. Seitliche Belastungen treten nicht auf p und ans diesem
Grunde kann auch das Material des Steges verhältnismäßig
D : ng t u
schwach gehalten werden was einen Teil des dadurch zusäts
lieherforderlichen Arbeiteganges wieder ausgleicht.
DieZeichnung geigt unter
1.) den federnden oder einen anderei (iv
2.) die drehbare Befestigung des federnden SchwenkbügelSs
8S) Ma 9
3) den Schwenkbereich des Knebels (360) p
4.) den nunmehr ebenfalls schwenkbaren Steg
5.) den Schwenkbereich des Steges (1800)
6. die Nietenachsep um welches sich der ; Steg drehtv
das Scharnier, in die Nietenachse befestigt istp
8.) den
Die Ausführung der Nummer7mannwiederumerfolgen indem
das Scharnier a. nf den Manschettenknopfboden als separates
Teil befestigt wird, oder aus dem Boden ausgepreßt wiTdo
In beiden Fällen ist es ohne Belange ob die Niotenachse
am Scharnier (Abba 1 ! 2) befestigt wird oder a-ia schwenk-
baren Steg c 5 e
My design of the cufflink bar by engaging a rotatable bearing on the cufflink base removes all of the above-mentioned deficiencies. The bearing makes it possible to pivot the cufflink bar at an angle of 1800, which means that any desired position is available at the desired times, and the most practical and the most inconspicuous as well as the most inconspicuous adjusts all by itself. This means that you can use your forearm completely b @ om during typing and without any noticeable handicap, because the cuff link is the "thickness"
Has lost any damage to the hinge
Trap to be expected, since the only burden in the
Inng goes into which the web follows through the rotary movement
gives. Lateral loads do not occur p and ans this
The material of the web can also be reasonably proportionate
D: ng do
be kept weak which adds a part of the result
compensates for the work required on loan.
The drawing violates
1.) the springy one or another (iv
2.) the rotatable attachment of the resilient swivel bracket
8S) Ma 9
3) the swivel range of the toggle (360) p
4.) the now also pivotable bridge
5.) the swivel range of the bridge (1800)
6. the riveting axis around which the; Bridge rotates
the hinge, attached to the rivet axis p
8.) the
Repeat the execution of the number 7man by
the hinge a. nf the cufflink base as a separate one
Part is attached, or pressed out of the ground wiTdo
In both cases it is irrelevant whether the rivet axis
attached to the hinge (Abba 1! 2) or a-ia swivel
bar c 5 e