Reisigbesebschoner 1951 bezeichnet sich das in Schmiedeeisen mit Stahlband
verfertigte Gebrauchsmuster. Der Reisigbesenschoner ist aus Einzelteilen zusammengeschweisst
und ist nicht an Norm gebunden, sodass für jede Besengrösse das Gebilde angefertigt
werden kann. Das Gebrauchsmuster ist nicht nur als Schoner der Besen anzusehen,
sonder kann auch nur als naitevorrichtung dienen. Durch die zusammengeschweisste
Hülse mit aufgestztem 45 mm langem 1" Rohr werden die Reisige am hinteren Ende zusammengehalten
und ein Auseinanderspreitzen der Ruten, nach Finführung des Stieles, ist mit Sicherheit
verhindert. Zwei senkrecht angebrachte 15 cm langen Igngsohenkel mit je einer Öse
ermöglichen eine Anbringung einer Stahlbanddrosselung in der Gegend der 2. Wiede.
Mit dieser abermaligen Haltevorrichtung (Stahlband mit Hebelzugverschluss) wird
bezweckt, die 2. Besenwied zu sichern und dem Besen selbst einen besseren Halt zu
geben. Der Reisigbesenschoner ist somit als Jdeal anzusehen, dass nicht nur gebundene
Ruten eingeführt werden können, sondern es können sogar lose, aneinandergefügte
Reisige eingespannt werden und ein Besen mit abgerissenen
Mieden kann bis zur natürlichen Abnitzung verwendet werden.
er Besenschoner wird zum Gebrauch zuerst auf den Be-
sen aufgesetzt und dann erst der Besenstiel in Starke des
Rohrstutzens eingeführt. Der Besenstiel wird bis über das
tahlba vorgetrieben, un die Ruten, noch mehr als sonst,
an a Stahlband zu pressen. Auch ein Lurohbrechen des
Stiels urch die Ruten, bei grossereo."'iderstand im Ge-
bruch, ist verhindert.
Lurch se. chgemsses Aufsetzen des-.. eisigbesenschoners und
richtiges Finführen des Stieles, der mittels einer Holzschraube gesichert ist, ist
eine totale Schonung und eine einwandfreie Befestigung des Reisigbesen oder der
losen
rauten eeben.
t
Schutzanspruch :
1./Hülse mit auf feststen Rohrstutzen, zur Hinfuhrmg
des Stiels.
2. J Langscherifel mit Öse und Führung des Stahlbandes.
3.) Stahlband zum Halt und zur Schonung der 2. ? iede.
4. Einfuhrung des Stieles und gegebene, noch bessere
Befestigung des Besens im Besenschoner.
Brush brush schooner 1951 is the name of the utility model made of wrought iron with a steel band. The brushwood broom protector is welded together from individual parts and is not bound by any standard, so that the structure can be made for any broom size. The utility model is not only to be seen as a protector for the broom, but can also only serve as a naite device. The welded-together sleeve with attached 45 mm long 1" tube holds the rods together at the rear end and the rods are prevented from spreading apart after the handle has been guided. Two vertically attached 15 cm long iron handles, each with an eyelet, make it possible to attach a rod Steel band throttling in the area of the 2nd Wiede.The purpose of this repeated holding device (steel band with lever pull closure) is to secure the 2nd broom wied and to give the broom itself a better hold.The brushwood broom protector is therefore to be regarded as a Jdeal, that not only tied rods can be introduced, but it can even be clamped loose, joined brushwood and a broom with torn off Avoided can be used until natural wear and tear.
he broom cover is first placed on the broom
sen put on and only then the broomstick in strength of
Pipe socket introduced. The broomstick will go above that
tahlba driven forward, and the rods, even more than usual,
to press on a steel band. Also a Luroh breaking des
stem through the rods, with greater reo."'iderstand in the
breakage is prevented.
Lurch se
Properly guiding the handle, which is secured by means of a wood screw, is a total protection and a perfect attachment of the broom or loose just diamonds.
t
Claim for protection :
1./sleeve with the most fixed pipe socket, for the feed mg
of the stalk.
2. J long scissors with eyelet and guide of the steel band.
3.) Steel band to hold and protect the 2nd ? either.
4. Introduction of the stalk and given, still better
Attachment of the broom in the broom cover.