Hexmann KatzenbergeT ia Graz-Eggenbergw
- -. r--.-
Druckplatte füT EisenbetonriT ende&ke.
Das Gebrauchsimster betrifft eine Ausbildung von Druck-
platten fSr Eisenbetonrippendecken. Semess der Nenernng weist
der DrLickteil der 21atte all seiner Oberseite eine Rippe auf.
Iüie
eine Lehre fnr das Niveau, des einzsbringenden FSllbetons ildet.
Die Höhe dieser Rippe rird zweckwässig auch so bemes"nj, dase
sie bei Stapel&ag die über ihr befindliche Drn&kplatte
an der
Unterseite berührt.
In der Zeichnung ist eine Druckplatte nach der ! feuerung
dargestellte und und zeigt zeigt l eine isenbetonrippendecke
im
Querschnitt nnd die Fig* einen Dru. skpis. ttenstapel.
Die Druckplatte besteht, wie übliche ans einem mittleren
Druckteil a und anschliessenden Schenkeln b die sich aof Flan-
sehen der Träger o abstützen Die Oberseite des Drtick-
telles a trägt in der latte eine Rippe die zo-einer Anffalla.
ng
des Betons e bis zu. deren Niveau zwingt, um eine ebene Decken-
oberseite zu erhalten.
2eckmässi ia. t die Hohe dieser Rippe d auch ec bemessen,
. pe d atio'h eo bemesseno
daas sie sich beim Uebereinanderleen von Brnckplatten nicht
nor
an die benachbarte Platte anlegte sondern dass aoh eine weitere
BerShr&nganzweidavonentferntenStellenstattfi.ndet(Fig).
'Die UnthtHlende der BerShrnngspnkte an der Oberseite entspricht
also im Wesen der Gestalt derUnterseite der Dra.skplatte<
Die Schenkel b sind# wie an sich bekannt ; zur Verstärkung.
der Anaohlusszone an den Druckteil a mit kcnsolartigen Ansätzen
f
ausgestattete Beim Ineinanderschieben liegen alsdann die Platten
satt in ihrer Mitte nnd an den beiden Ansätzen an, wodurch
die
schrägen Schenkel der Ylatten besser gepen : Beschädkung oder
Drack geschützt sind
Schutzanaprlloh.
Druckplatte für Bisenbetonrippendecken, bestehend aus
einem mittleren Drackteil nnd schräg abwärts gerichteten Sehen-'
key dadurch gekennzeichnete dass der Druckteil (a) an seiner
Oberseite eine Rippe (d) aufweist, die parallel zu den Zecken-
trägern (c) über die ganze Tiefe der Druckplatte läaftcnd dass
ur Stapelang die Umhüllende der BerQhrnngspunkte der Brock-
platten der Gestalt der Unterseite derLetzteren gleichkommt
wobei vorzugsweise die Schenkel an ihrer Auschlasszone an ü
Dru. ckteil verstärkt sind,
Hexmann Katzenberge T ia Graz-Eggenbergw
- -. r--.-
Pressure plate for EisenbetonriT end&ke.
The utility semester relates to the training of pressure
plates for reinforced concrete ribbed floors. Semess the name points
the press portion of the 21 has a rib on all of its top. Hey
a gauge of the level of the revenue-generating cast concrete.
The height of this rib is appropriately calculated as follows
she at stack&ag the drink&kplate above her on the
bottom touched.
In the drawing, a printing plate after the ! firing
Illustrated and and shows l shows a ribbed concrete slab im
Cross section and the fig* a pressure. scpis. pile of dead.
The pressure plate consists, as usual, of a middle one
Pressure part a and adjoining legs b which are located aof flange
see the carrier o support the top of the push-
telles a carries in the latte a rib which zo-an Anffalla. ng
of concrete e up to. whose level forces a flat ceiling
to get top.
2eckmäsi ia. t measure the height of this rib d also ec,
. pe d atio'h eo bemesseno
that they do not differ when laying bridge plates one on top of the other
applied to the adjacent plate but that aoh another
BerShr&ntakes place in two remote locations(Fig).
'The limit of the crossing points at the top corresponds to
thus in essence the shape of the underside of the Dra.skplatte
The legs b are known as such; for reinforcement.
the connection zone to the pressure part a with cnsol-like attachments f
equipped When sliding into each other then lie the plates
snugly in their middle and at the two approaches, whereby the
oblique leg of the Ylatten better gepen : damage or
are protected
protective attack
Pressure plate for Bisenbeton ribbed ceilings, consisting of
a middle drack part and obliquely downward facing eyes-'
key characterized in that the pressure part (a) at its
has a rib (d) running parallel to the tick
carriers (c) over the entire depth of the pressure plate and that
only stacking the envelope of the crossing points of the Brock
plates equaling the shape of the underside of the latter
preferably the legs at their Auschlasszone ü
Dru. are reinforced