Stahls4hraak
Gegenstand der 1feues ist die besondere Ausbildung eines Stahl-
obrankestvornehmlichzur Aufnahme von verstellbaren Einlegeboden*
Zum Zwecke der Verstellbarkeit der Einlegeboden werden bekanntlich
eigens zur Aufnahme der Traghaken bestim&te Zahnleisten
in die Schran-
ke eingebaut Abgesehen davon dass durch die Anordnung der Zahnleisten
an vier Auflegestellen ia Schrankinneren viel Platz verlorengeht)
; er-
fordern Herstellung und Aubringung dieser Einrichtung erhöhte
Aufwaum
dungen, die sich verteuernd auf den Verkautspreis des St&hlechrankea
auswirken.
Bei der AusfihrMngsform des Stithlschrankes gea ! äss der Neuerung
werden
an den vier Schrankkanten kastenförmige Vor-oder Rtcksprnnge
ange-
ordnet die durch entsprechende Xantung der Seiten-und RLiekwände
das
Schrankes unmittelbar gebildet werden. Diese kastenförmigen
Vor- oder
Riickspränge verleihen dem Stahlsehranle eine ganz besonders
hohe Sta-
bilität auch für den Fall wo sehr schwaches Stahlblechmaterial
zr
Verwendung gelangte Besonders vorteilhaft ist die Möglichkeit
der un-
mittelbaren AnbringMng der Ausstanzungen zur Aufntthme der
Traghaken
für die Einlegeböden an den Begrenzungswänden des Schrankes
selbwt
und zwar in Bereich der Abdeckung durch die kastenförmige Abkantung<
An der Zeichnung wird die Neuerung näher erläutert.
Figur 1 zeigt den Langsquerschnitt durch einen Stahlachrank
gemäss
der Neuerung#
Figur 2 den Teilquerschnitt durch eine Seitenwtndbegranzungt
Figur 3 den Längsteilquerschnitt vom Schrankinneren aus geseheno
Die SeitenbegrenzTmgswand 1 beeitzt-nach der Schrankrückwand
zu die
kastenförmige Abkantung 2 deren offene Seite durch die Sohrankruck-
wand 3 nach dem Schrsnkinneren zu abgedeckt ist wobei die Abkantung
4
der Schrankrückwand zu deren Stabilisierung und zur Anlehnung
gegen
die Seitenwand l diente Die Befestigung der Seitenwand 1 und
Rückwand ?
erfolgt zweckmässig a. ber den Flansch 5 an der Ablc « ttung
2v t
bleibt die Seitenwand 1 ohne sichtbare Verbindungamittel und
die Ter
bindung an der Schrankrü. ckwand 3 von anasen nicht erkennbar.
Der im
Bereich der Kasteaabkantung 2 befindliche Teil der Rückwand
3 erhälti
-
die Ausstanzungen 6 zur Aufnahme der Traghaken 7 gar die Einlegeböden
8
Es erübrigt sich also hier die Anordnung einer besonderen Zahnstange.
Die Seitenwand 1 wird nach der vorderen Scarankeeite zu mit
der etwas
tieferen kastenförmigen Abkantung 9 versehen, wobei die Tiefe
der Ab-
kantung eich nach der Stärke des Torblattes richtet In dem
so entstan-
denen Hohlraum lo wird die Stützleiste 11 mit den Aussparungen
12 zur
Aufnahme des Traghakens 7 untergebrcht. Diese Stützleiste 11
dient
gleichzeitig zur stabilen Befestigung der Türgehänge und Sohlossarmatu-
ro.
Die kastenförmigen Abkantungen 2 und 9 können auch entgegen
der Dar-
stellung in der Zeichnung so vorgesehen werden, dass der Rücksprung
seitlich in Erscheinung tritt « Beispieslweise kann die kastenförmige
Abkantung 2 aus der Rückwand 3 gebildet werden, während die
Seiten-
wand 1 nur die flanschfôrmige Abkantung 4 erhält
Schutzunsprilches
Stahls4hraak
The subject of 1feues is the special training of a steel
obrankest mainly to accommodate adjustable shelves *
For the purpose of adjustability of the shelf are known
Toothed strips specially designed to accommodate the support hooks in the cabinet
ke built in Apart from that by the arrangement of the toothed racks
a lot of space is lost at four support points, generally inside the cabinet); he-
require the production and installation of this facility increased effort
the price of the St & hlechrankea
impact.
With the version of the chair cabinet gea! according to the innovation
box-shaped front or rear jumps attached to the four cabinet edges
arranges the by corresponding Xantung of the side and back walls
Closet can be formed immediately. These box-shaped front or
Setbacks give the Stahlsehranle a particularly high status.
also for the case where very weak sheet steel material zr
The possibility of un-
indirect attachment of the cut-outs for receiving the support hooks
for the shelves on the partition walls of the cabinet itself
in the area of the cover through the box-shaped bevel <
The innovation is explained in more detail on the drawing.
Figure 1 shows the longitudinal cross-section through a Stahlachrank according to
the innovation #
FIG. 2 shows the partial cross-section through a side wall border
FIG. 3 shows the partial longitudinal cross-section from the inside of the cabinet
The side delimiting wall 1 beeitzt-after the cabinet rear wall to the
box-shaped fold 2, the open side of which through the Sohrankruck-
wall 3 is covered after the inside of the cabinet, whereby the fold 4
the cabinet back wall to stabilize it and to lean against it
the side wall l was used The fastening of the side wall 1 and rear wall?
takes place appropriately a. Via the flange 5 on the drain 2v t
the side wall 1 remains without any visible connection means and the ter
binding to the cabinet door. Back wall 3 of anases not recognizable. The im
Area of the Kasteaabkantung 2 located part of the rear wall 3 receives
-
the cutouts 6 for receiving the support hooks 7 even the shelves 8
There is therefore no need to arrange a special rack.
The side wall 1 becomes towards the front scaran side with the something
provided deeper box-shaped fold 9, the depth of the
edging is based on the thickness of the door leaf.
which cavity lo is the support strip 11 with the recesses 12 to
Recording of the support hook 7 interrupted. This support bar 11 is used
at the same time for the stable fastening of the door hangers and socket armature
ro.
The box-shaped folds 2 and 9 can also be contrary to the Dar-
position in the drawing so that the return
Appears to the side «For example, the box-shaped
Bevel 2 are formed from the rear wall 3, while the side
wall 1 only receives the flange-shaped fold 4
Protection against