Modellbezeichnun :
Zahnbürste.
Die Neuerung b'ioht sich auf eine Zahnbürste.
Bei den bekannten Zahnbürsten ist der Stiel in
der Regal in der gleichen Ebene des Borstenträgers d
d. h. lu Verlängorung des Bcrstenträgers ausgobildet.
Elne derartige Ausbildung der Zahnbürste hat
aber iu Gebrauch den Nuchteil, duß der Stiel hinder-
lich ist und lait einer solchen Zahnbürste die Innen-
flächen der Zihne sehr schlecht xu erreichen uind,
so dieseFlüchen eih&uhgenüßdhden. ReinituAg er-
fahren.
Die hufgubo der Neuerung besteht darin, den
angeführten Mangel tu beseitigen und den Stiel CM
Borstentrüger von boliebiger Form derart :'. nxuord-
non, daß derselbe nicht hinderlich ist und souit
uch die Innenflächen der Zähno bequem u errei-che1
sind.
Die : 3e Aufgabe ist gen O dor Neuerung dudurch
erreichte dur der Stiel gegen die ebene den Bor-
stentrugers im schwachen Kinkel nach oben verläuft.
Die neuerung ist auf der Zeichnung beispiels-
weise dargestellt-
Fig. 1 zeigt beispielsweise eine Zahnbürste mit
gerade verlaufenden Borstenträger 1 bei welchem der
Stiel 2 an einem Ende angesetzt ist und een die
E ! bene des Borstenträgers im schwachen Kinkol naoh
oben vorlüuft.
Anstatt sich der Htiel am Rnde les Borntenträ-
gers anschließt, kann sich dorselbe auch, wie z. B.
Fig. 2 zoigt, etwa auf der Mitte doo BorstuntrMer-
rückenu anschließen.
Selbstverständlich knn die neue Stiel-Anord-
nung such bei konvex oder kontav ausgebildeten Bor-
stenträiern Verwendwng finden. Fi-3 Keigt beispiols-
weise die Neuerung bei einer Zahnbürste mit konvex
ausgebildetem Borst'ntruger und Fi. 4 eine lnbUrste
mit kontav ausgebildotem BorstentrUer.
Die Neuerung iot solbstverständlich nicht uf
die dargestellton AuftilTrunsbeispiolu beschränlte
vielmehr sind im Hhen der Neuerung uch no'.'h an-
doro Aucfuhrunon uölich no K. 3. knu der ti'1
e1 « 3rt3 AUw ulus ; ¢ ? ; 0 7. * tz ßz tif31
. uc: eino nch oben odr untun goboeno yor. uf-
weisen. 7 ('rn' r knn uch er tiel loubar am Bortun-
träger efeutigt ein.'eitor kann auch das riiel-
onde, wie in Pi. 1 punktiert njedoutet, nach oben
oder unten geboten verlaufen.
Model name:
Toothbrush.
The innovation is based on a toothbrush.
The handle of the known toothbrushes is in
the shelf in the same plane as the bristle carrier d
ie lu extension of the brush holder.
Elne toothbrush design has this kind of design
but iu use the nuchal part so that the stem prevents
the interior of such a toothbrush is and
surfaces of the teeth very poorly xu reach uind,
so these curses eih & uhgenüßdhden. Purity
travel.
The hufgubo of the innovation is the
remove the deficiency mentioned and remove the stem CM
Bristle deceiver of boliebiger form like this: '. nxuord-
non, that it is not a hindrance and is souit
The inner surfaces of the teeth can also be comfortably reached1
are.
The third task is towards innovation by means of it
reached the stem against the plane of the bor-
stentrugers runs upwards in the weak kinkel.
The innovation is shown on the drawing as an example
presented wisely-
Fig. 1 shows, for example, a toothbrush with
straight bristle carrier 1 in which the
Stalk 2 is attached at one end and een the
E! level of the bristle carrier in the weak Kinkol naoh
upstream.
Instead of the Htiel on the edge of les Borntenträ-
gers can be followed by the same, such as B.
Fig. 2 zoigt, approximately in the middle doo BorstuntrMer-
connect back.
Of course, the new handle arrangement can
search for convex or contavoidal boron
stentrae find use. Fi-3 Keigt example-
wise the innovation in a toothbrush with convex
trained bristle carrier and Fi. 4 a brush
with continuously trained bristle turret.
The innovation is of course not uf
the depicted on AuftilTrunsbeispiolu limited
rather, in the height of the innovation uch no '.' h an-
doro Aucfuhrunon uölich no K. 3. knu der ti'1
e1 «3rt3 AUw ulus; ¢? ; 0 7. * tz ßz tif31
. uc: eino nch above or untun goboeno yor. uf-
point. 7 ('rn' r knn uch he tiel loubar on the Bortun
carrier efeutigt.'eitor can also use the
onde, as in Pi. 1 dotted njedoutet, upwards
or run down below.