<Desc/Clms Page number 1>
Anordnung zum Schutze von Senderöhren gegen Überlastung Die Erfindung betrifft eine Anordnung zum Schutze von Senderöhren gegen Überlastung, insbesondere zum Schutze des Schirmgitters, wobei jedoch gleichzeitig die Anode geschützt wird. Es sind bereits verschiedene Anordnungen zum Schutze von Senderöhren gegen Überlastung bekannt. Zwecks Erläuterung der Erfindung wird nachstehend an Hand der Fig. 1 eine bekannte Schaltung erklärt.
Die Figur zeigt die sog. Clamp-Schaltung, die nur einen Zweck erfüllt. Bei fehlender Aussteuerung wird die Schirmgitterspannung begrenzt, damit sie nicht auf volle Anodenspannung hochgeht. Bei vorhandenem Gitterstrom, also während des Sen- dens, ist die Clamp-Röhre gesperrt und wirkungslos. Sie arbeitet also während des Sendebetriebes überhaupt nicht.
Die Senderöhre kann jedoch vor allem während der Arbeitsphase überlastet werden, entweder durch zu grossen Schirmgitterstrom, wenn die Antennenkopplung während des Abstimmens zu lose ist oder im umgekehrten Fall, wenn durch Verstimmen oder zu fester Kopplung der Schirmgitterstrom zu klein wird und dadurch die Schirmgitterspannung zu hoch ansteigt, was gleichzeitig einen zu grossen Anodenstrom und damit eine Anodenüberlastung zur Folge hat. Während der Sendepause muss sie natürlich ebenfalls einen Röhrenschutz durch Begrenzen der Schirmgitterspannung übernehmen.
Die erfindungsgemässe Anordnung zeichnet sich dadurch aus, dass ein verstärkendes Schaltelement, z. B. eine Elektronenröhre oder ein Transistor, eingebaut ist, das bei zu gross werdender Schirmgitterspannung den Strom übernimmt und bei zu gros- sem Schirmgitterstrom die Schirmgitterspannung fallen lässt.
Im Ausführungsbeispiel des Erfindungsgegenstandes gemäss Fig. 2 findet eine Mehrgitter- röhre Rö < . Anwendung. Röi ist die zu schützende Senderöhre, St ein Stabilisator oder eine Glimmlam- penstrecke, deren Brennspannung etwa der Betriebsspannung des Schirmgitters entspricht. R ist der Schirmgitter-Vorwiderstand, der zur Spannungsquelle für das Schirmgitter führt und gegebenenfalls auch an die Anodenspannung gelegt werden kann. Anhand der Fig. 3 wird die Arbeitsweise der Anordnung nach Fig. 2 erläutert.
Wird der Schirmgitterstrom zu gross, fällt an R die Spannung ab, die Schirmgitterspannung sinkt und die Schirmgitterlei- stung 0,2 = 1,2 . Ub" wird nicht überschritten. Wird der Schirmgitterstrom klein, geht die Schirmgitterspannung nur so weit in die Höhe, bis durch Gittersteuerung über die Glimmstrecke St in Rö2 Anodenstrom fliesst und damit ein weiteres Ansteigen der Schirmgitterspannung verhütet wird. Durch Festhalten von U.2 wird gleichzeitig ein Ansteigen des Anodenstromes der Senderöhre vermieden.
Im Falle von Anodenmodulation kann eine Drossel verwendet werden, um trotz der beschriebenen Gleichspan- nungs- bzw. Gleichstrombegrenzung die z. B. ton- frequente Mitmodulation des Schirmgitters zuzulassen.
<Desc / Clms Page number 1>
Arrangement for protecting transmission tubes against overload The invention relates to an arrangement for protecting transmission tubes against overload, in particular for protecting the screen grid, but at the same time protecting the anode. Various arrangements for protecting transmission tubes against overload are already known. For the purpose of explaining the invention, a known circuit is explained below with reference to FIG.
The figure shows the so-called clamp circuit, which only serves one purpose. If there is no modulation, the screen grid voltage is limited so that it does not go up to full anode voltage. If the grid current is present, ie during transmission, the clamp tube is blocked and ineffective. So it does not work at all during transmission.
However, the transmitter tube can be overloaded, especially during the working phase, either by too large a screen grid current if the antenna coupling is too loose during tuning or, in the opposite case, if the screen grid current becomes too small due to detuning or too tight coupling and thus the screen grid voltage is too high increases, which at the same time results in an anode current that is too high and thus an anode overload. During the pause in transmission, it must of course also take over tube protection by limiting the screen grid voltage.
The inventive arrangement is characterized in that a reinforcing switching element, for. B. an electron tube or a transistor is built in, which takes over the current when the screen grid voltage becomes too high and drops the screen grid voltage when the screen grid current is too high.
In the exemplary embodiment of the subject matter of the invention according to FIG. 2, there is a multigrid tube Rö <. Application. Röi is the transmitter tube to be protected, St a stabilizer or a glow lamp section, the burning voltage of which corresponds roughly to the operating voltage of the screen grid. R is the screen grid series resistor, which leads to the voltage source for the screen grid and, if necessary, can also be connected to the anode voltage. The mode of operation of the arrangement according to FIG. 2 is explained with reference to FIG.
If the screen grid current becomes too high, the voltage at R drops, the screen grid voltage drops and the screen grid power 0.2 = 1.2. Ub "is not exceeded. If the screen grid current is low, the screen grid voltage only increases until anode current flows through the grid control via the glow path St in Rö2, thus preventing a further increase in the screen grid voltage. Holding U.2 simultaneously an increase in the anode current of the transmitter tube is avoided.
In the case of anode modulation, a choke can be used, in spite of the described direct voltage or direct current limitation, B. to allow tone-frequency modulation of the screen grid.