Haltevorrichtung an Ringbuchordner Haltevorrichtungen an Ringbuchordnern mit zwei teiligen, aufklappbaren Aufreihbügeln sind in ver schiedenen Ausführungsformen bekannt, und zwar sowohl solche mit runden als auch solche mit recht eckigen Aufreihbügeln. Haltevorrichtungen mit run den Aufreihbügeln haben den Vorteil, dass sich darin das Einlagegut schnell und leicht umblättern lässt, weil die Aufreihbügel ungefähr einen Kreis beschrei ben.
Sie haben aber den Nachteil, dass sie nicht für Ordner mit Register verwendet werden können, weil die Blätter durch den Radius der Aufreihbügel an der Vorderkante eine konvexe und an der Hinter kante eine konkave Fläche bilden, so dass ein Teil des Registers verdeckt wird. Auch wird dadurch das gute Aussehen des Ordners beeinträchtigt. Dieser Nachteil ist nicht vorhanden bei Verwendung von rechteckigen Aufreihbügel'n. Diese haben aber wie derum den Nachteil, dass sie nur für Ringbücher mit flachem Rücken verwendbar sind bzw. dass ein gewölbter Buchrücken infolge der flachen Ausge staltung der Aufreihbügel keinen guten Halt hat.
Ausserdem müssen die Blätter beim Umschlagen immer erst etwas angehoben werden. Schliesslich liegen bei allen bekannten Bügelformen die Stoss stellen der Bügelteile am oberen Scheitelpunkt der Bügel und damit bei geschlossenem Buchdeckel gegen dessen Innenseite an und können diesen beschädigen, wenn die Ordner in der Rückenhöhe eng gehalten sind, da sich an den Stossstellen eine Gratbildung nie ganz vermeiden lässt.
Die Erfindung vermeidet diese Nachteile. Sie besteht darin, dass die dem Buchrücken zugekehrten hinteren Hälften der Aufreihbügel teilringförmig aus gebildet sind, während die vorderen Bügelhälften im mittleren Teil geradlinig und rechtwinklig zum Buch boden verlaufen und am oberen Ende zum Buch rücken hin abgebogen sind. Die Aufreihbügel kön- nen vorzugsweise so geformt sein, dass ihre Scheitel im Bereich der vorderen Ringhälften und die Stoss stellen der Bügelhälften tiefer als die Scheitel liegen.
Durch diese Form der Aufreihbügel wird einer seits eine Verformung der gewölbten Buchrücken auch nach längerem Gebrauch vermieden und ein leichtes Umschlagen des Einlagegutes gewährleistet, während anderseits eine stets ebene und damit für ein Register ideale und ausserdem gut aussehende Stirnfläche des Blätterblocks garantiert ist. Auch Beschädigungen an der Innenseite des Buchdeckels können nicht mehr vorkommen, da die Stossstellen der Bügelteile nicht mehr mit dem Buchdeckel in Berührung kommen.
Darüber hinaus. ermöglicht diese Erfindung die Anbringung der Aufreihbügel un mittelbar am Deckelfalz der Mappe, wodurch die Deckel schmaler gehalten werden können und sich eine wirtschaftliche Herstellung srgbt.
In der Zeichnung ist ein Ausführungsbeispiel der Erfindung dargestellt, und zwar zeigt die Abbildung eine Seitenansicht der Rückenpartie eines mit der neuen Haltevorrichtung ausgestatteten Ringbuch ordners. Nach der Erfindung sind die dem gewölbten Buchrücken 1 zugekehrten hinteren Hälften 2 der Aufreihbügel teilringförmig ausgebildet, während die vorderen Bügelhälften 3 im mittleren Teil gerad linig und rechtwinklig zu den Buchdeckeln 4 und 5 bei geschlossenem Ordner verlaufen und am oberen Ende nach hinten abgebogen sind.
Die umgebogenen Enden 6 bilden mit den geradlinigen Teilen 3 spitze Winkel, so dass die Stossstelen 7 der Bügelhälften 2 und 3 tiefer liegen als die Scheitelpunkte der Bügel hälften 3. Infolgedessen können die Stossstellen 7, an denen meistens scharfe Kanten vorhanden sind, nicht mehr mit dem Buchdeckel 5 in Berührung kom- men. Tiefer bezieht sich dabei auf den Höhen abstand in bezug auf den Ordnerboden.
Holding device on ring binder holding devices on ring binder with two-part, hinged mounting brackets are known in various embodiments, both those with round and those with rectangular mounting brackets. Holding devices with round strapping brackets have the advantage that the insert can be turned over quickly and easily because the aligning brackets roughly describe a circle.
However, they have the disadvantage that they cannot be used for files with registers because the sheets form a convex surface at the front edge and a concave surface at the rear edge due to the radius of the aligning bar, so that part of the register is covered. It also affects the good looks of the folder. This disadvantage does not exist when using rectangular mounting brackets. However, these in turn have the disadvantage that they can only be used for ring binders with a flat spine or that a curved book spine does not have a good hold due to the flat design of the strapping bracket.
In addition, the sheets always have to be lifted a little before being turned over. After all, with all known bow shapes, the joints of the bow parts are at the upper apex of the bow and thus against the inside of the cover when the book cover is closed and can damage it if the files are kept close at the back, since burrs can never be completely avoided at the joints leaves.
The invention avoids these disadvantages. It consists in the fact that the rear halves of the aligning bracket facing the book spine are formed partially ring-shaped, while the front bracket halves in the middle part run straight and at right angles to the book bottom and are bent back towards the book at the top. The stringing brackets can preferably be shaped in such a way that their apexes are in the area of the front ring halves and the joints between the bracket halves are lower than the apexes.
This form of the stringing bracket on the one hand avoids deformation of the curved book spine even after prolonged use and ensures easy turning of the insert, while on the other hand an always flat and therefore ideal for a register and also good-looking face of the block of pages is guaranteed. Damage to the inside of the book cover can no longer occur either, since the joints between the bracket parts no longer come into contact with the book cover.
Furthermore. This invention enables the mounting bracket to be attached directly to the cover fold of the folder, which means that the cover can be kept narrower and economical production is srgbt.
In the drawing, an embodiment of the invention is shown, namely the figure shows a side view of the back of a ring binder equipped with the new holding device. According to the invention, the curved book spine 1 facing rear halves 2 of the stringing bracket are partially ring-shaped, while the front bracket halves 3 in the middle part straight and at right angles to the book covers 4 and 5 with the folder closed and are bent back at the top.
The bent ends 6 form acute angles with the rectilinear parts 3, so that the pushrods 7 of the bracket halves 2 and 3 are lower than the vertices of the bracket halves 3. As a result, the joints 7, which are mostly sharp edges, can no longer be used the book cover 5 come into contact. Lower refers to the height distance in relation to the folder base.