<Desc/Clms Page number 1>
EMI1.1
Walze aus Beton oder dergl. Kunststein mit Metallgerippe.
Den Gegenstand der vorliegenden Erfindung bildet eine Walze aus Beton oder dergl.
Kunststein, welche bestimmt ist, die bei verschiedenen Industrien verwendeten Metallwalzen zu ersetzen, da letztere den Nachtheil haben, dass sie bei Verwendung im Wasser oder in feuchter Atmosphäre, falls sie aus Eisen hergestellt sind, leicht rosten, oder, wenn sie zur Verhütung des Rostens mit Bronzemanteln umgeben werden, sehr theuer sind.
Ausserdem biegen die Walzen bei schwächerer oder hohler Construction sich sehr leicht durch oder sie geben nach. Alle diese Übelstande werden durch die Beton-oder dergl.
Knnststeinwalzen vermieden. Ausserdem haben diese Walzen den Vorzug, dass das damit
EMI1.2
bei d drr Papierfabrication für die nasse Papiermasse von grossem Wert ist.
Da jedoch der Beton oder dergl. Kunststein für sich allein zur Herstellung von Walzen sich nicht eignet, d. h. nicht die genügende Sicherheit gegen Bruch bietet, so wird derselbe der ovrligenden Erfindung zufolge durch ein besonderes Metallgerippe zusammengehalten und mit einer durchgehenden Metallwelle versehen, wie dies aus beiliegender Zeicknung ersichtlich ist.
In derselben veranschaulicht Fig. 1 eine Ansicht der Walze, wahrend Fig 2 einen Längsschnitt durch das (Gerippe derselben nach Linie der Fig. 3 und Fig. 3 einen m-rchaitt nach Linie B-B der Fig. 2 darstellt.
An der durchgehenden Welle 1, welche, um eine bessere Verbindung mit der Masse 111 erzielen, zweckmässig aufgerauht, mit Einschnitten, vorstehenden Stiften oder dergl. ver-
EMI1.3
befestigt, deren Enden durch Längsstaugen 3 aus Winkel-, Flach- oder Rundeisen parallel mit der Mantelfläche und in gleichem Abstande von der Welle miteinander verbunden werden.
In das so gebildete Gfrippe wird der Beton oder Kunststein eingestampft, so dass er dasselbe vollständig ausfüllt und die Längsstangen 3, um welche zweckmässig noch Urahtringe oder Bänder zur grösseren Versteifung gelegt werden, noch mit einer entsprechenden Schicht bedeckt, sowie seitlich bis an die auf der Welle befestigten Metallscheiben 5 heranreicht, wie in der Zeichnung mit gestrichelten Linien dargestellt ist. Die Wiilic, werden sodann auf der Drehbank genau centriert und kann z. B. für die Papierfabrication die Oberfläche derselben noch mit Fluaten gehärtet, glatt geschliifen und auf Hochglanz poliert werden.
**WARNUNG** Ende DESC Feld kannt Anfang CLMS uberlappen**.
<Desc / Clms Page number 1>
EMI1.1
Roller made of concrete or similar artificial stone with a metal frame.
The subject of the present invention forms a roller made of concrete or the like.
Artificial stone, which is intended to replace the metal rollers used in various industries, since the latter have the disadvantage that they rust easily when used in water or in a humid atmosphere, if they are made of iron, or when they are used to prevent rusting are surrounded with bronze cloaks are very expensive.
In addition, with a weaker or hollow construction, the rollers bend very easily or they give way. All of these inconveniences are caused by the concrete or the like.
Artificial stone rolling avoided. In addition, these rollers have the advantage that that with it
EMI1.2
at the drr paper factory is of great value for the wet pulp.
However, since the concrete or the like. Artificial stone on its own for the production of rollers is not suitable, i. H. does not offer sufficient security against breakage, it is held together according to the present invention by a special metal frame and provided with a continuous metal shaft, as can be seen from the accompanying drawing.
In the same, FIG. 1 illustrates a view of the roller, while FIG. 2 shows a longitudinal section through the (skeleton of the same along the line in FIG. 3 and FIG. 3 shows a m-rchaitt along line B-B in FIG.
On the through shaft 1, which, in order to achieve a better connection with the mass 111, expediently roughened, with incisions, protruding pins or the like.
EMI1.3
attached, the ends of which are connected to each other by longitudinal stems 3 made of angle, flat or round iron parallel to the outer surface and at the same distance from the shaft.
The concrete or artificial stone is tamped into the Gfrippe formed in this way so that it completely fills it and the longitudinal rods 3, around which ureline rings or ribbons are conveniently placed for greater stiffening, are still covered with a corresponding layer, as well as laterally up to the Metal disks 5 attached to the shaft, as shown in the drawing with dashed lines. The Wiilic are then precisely centered on the lathe and can e.g. B. for paper production the surface of the same can be hardened with fluates, sanded smooth and polished to a high gloss.
** WARNING ** End of DESC field may overlap beginning of CLMS **.