<Desc/Clms Page number 1>
EMI1.1
EMI1.2
<Desc/Clms Page number 2>
EMI2.1
den Kontakt 6 so auf der Trommel 2 anordnen, dass er mit dem Kontakt 7 nur dann in Berührung kommt, wenn sich ein volles Filmbild auf der Zielscheibe befindet.
Um das sichere Hemmen des Kinematographen auch beim Überschreiten des Kontaktes 6' über den Kontakt 7, ohne dass hiebei der Kinematograph vollständig, angehalten wurde. zu erzielen, ist ferner ein Kontakt 8 vorgesehen, der sich ebenfalls im gleichen Stromkreis wie die Magnete 3 und 10 befindet. Der drehbare Anker ist mit einem federnden Kontakt. 9 versehen. der so angeordnet ist, dass für gewöhnlich die Kontakte 8 und 9 unterbrochen sind.
Wird nun der Kontakt 6,7 unterbrochen, bevor der Kinematograph vollständig gehemmt wurde, so bewirkt der Momentkontakt zwischen 6 und 7 eine geringe Bewegung des Ankers 4, wodurch der Kontakt 9 mit dem Kontakt 8 in Berührung kommt und so den Stromkreis schliesst, der auf die nachstehend beschriebene Weise den Kinematographen sperrt.
Als weitere Sicherung für das Hemmen des Kinematographen sind im gleichen Stromkreis
EMI2.2
die Kupplung bewirkende Magnet während der Bewegung des Films in den Stromkreis eingeschaltet ist, so dass der Magnet erregt und die mit der Welle 1 verbundene Scheibe 13 angetrieben wird. Beim Abgeben eines Schusses wird die Kupplung gelöst, so dass der Teil 12 frei laufen kann, ohne die Scheibe 13 mitzunehmen ; gleichzeitig wird der Stromkreis der Magnete J
EMI2.3
die Primärwicklung eines Transformators 16 angeschlossen, während eine Batterie 17 diesen Stromkreis speist. Das Mikrophon 14 wird zweckmässig in einem trichterförmigen Behälter angeordnet.
Da der primäre Stromkreis ausserordentlich schwach ist. empfiehlt es sich, ein besonders empfindliches Relais zu verwenden. Ein solches Rela@s kann z. H. aus einer abgestimmten Stahl-
EMI2.4
folgend beschriebene Stromkreis unterbrochen wird.
An die Kontaktfederm 19 sind die Leitungsdrähte 22 und eine Batterie 23 angeschlossen.
Die Drähte 22 führen zu einem Elektromagneten 2. Für gewöhnlich ist der Magnet 7 erregt.
@ so dass der Anker 25 angezogen ist. wodurch der die elektromagnetische Kupptung beeinnussetute
Stromkreis geschlossen ist.
Wird der Strom in den Transformator 16 geschickt, so wird das Relais 18 eerregt und infolge- dessen werden die Kontakte 20 unterbrochen. Das Relais 24 wird stromlos und der Anker 2 :) fällt dann unter Wirkung der Feder 26 herunter und schliesst durch die Kontakte 27 und 28 zwei andere Stromkreise, durch die erstens der Magnet 29 erregt wird. und den Anker 2j in seiner ge- senkten Lage festhält und zweitens der Solenoid 49 erregt wird.
Der Magnet 29 wird in folgender Weise erregt : Von der Batterie 30 fliesst Strom durch
EMI2.5
<Desc/Clms Page number 3>
EMI3.1
EMI3.2
**WARNUNG** Ende DESC Feld kannt Anfang CLMS uberlappen**.
<Desc / Clms Page number 1>
EMI1.1
EMI1.2
<Desc / Clms Page number 2>
EMI2.1
Arrange the contact 6 on the drum 2 in such a way that it only comes into contact with the contact 7 when a full film frame is on the target.
In order to safely inhibit the cinematograph even when the contact 6 'is passed over the contact 7 without the cinematograph being completely stopped. To achieve this, a contact 8 is also provided, which is also in the same circuit as the magnets 3 and 10. The rotatable armature is with a resilient contact. 9 provided. which is arranged so that the contacts 8 and 9 are usually interrupted.
If the contact 6, 7 is now interrupted before the cinematograph was completely inhibited, the momentary contact between 6 and 7 causes a slight movement of the armature 4, whereby the contact 9 comes into contact with the contact 8 and thus closes the circuit that opens locks the cinematograph in the manner described below.
As a further safeguard for the inhibition of the cinematograph are in the same circuit
EMI2.2
the clutch causing the magnet is switched on during the movement of the film in the circuit, so that the magnet is excited and the disk 13 connected to the shaft 1 is driven. When firing a shot, the clutch is released so that the part 12 can run freely without taking the disc 13 with it; at the same time the circuit of magnets J
EMI2.3
the primary winding of a transformer 16 is connected, while a battery 17 feeds this circuit. The microphone 14 is expediently arranged in a funnel-shaped container.
Because the primary circuit is extremely weak. it is recommended to use a particularly sensitive relay. Such a Rela @ s can, for. H. from a coordinated steel
EMI2.4
circuit described below is interrupted.
The lead wires 22 and a battery 23 are connected to the contact spring 19.
The wires 22 lead to an electromagnet 2. Usually the magnet 7 is excited.
@ so that the anchor 25 is tightened. whereby the innussetute the electromagnetic coupling
Circuit is closed.
If the current is sent to the transformer 16, the relay 18 is excited and as a result the contacts 20 are interrupted. The relay 24 is de-energized and the armature 2 :) then falls down under the action of the spring 26 and closes two other circuits through the contacts 27 and 28, through which the magnet 29 is excited. and holds the armature 2j in its lowered position and, second, the solenoid 49 is energized.
The magnet 29 is excited in the following way: Current flows from the battery 30
EMI2.5
<Desc / Clms Page number 3>
EMI3.1
EMI3.2
** WARNING ** End of DESC field may overlap beginning of CLMS **.