<Desc/Clms Page number 1>
Formsteinpresse mit gleichzeitig gegeneinander beweglichen Pressstempeln.
Die bisher gebräuchlichen Maschinen zum Pressen von Trümmergestein u. dgl. wurden in verschiedenen Formen ausgeführt, unter welchen jene Maschinen bemerkenswert sind,
EMI1.1
Pressstempeln erfolgt. Dieses doppelseitige Pressen wurde mit Hilfe hydraulischen Druckes oder anderer geeigneter mechanischer Mittel erreicht. Die Einrichtungen hatten aber den Nachteil, dass die beiderseitige Pressung niemals eine vollkommen gleichzeitige sein konnte, denn es war nötig, dass der Druck von oben nach unten und infolgedessen der seitens der zusammengepressten Masse entgegengesetzte Widerstand einen gewissen Betrag erreichte.
EMI1.2
werden.
Um diesen Übelständen zu begegnen, wurden zwar Einrichtungen vorgeschlagen, mittelst welcher ein gleichzeitiger doppelseitiger Druck erzielt wird, jedoch weisen diese den Nachteil auf, dass dabei die Konstruktion der Presse umständlich und teuer war und der Betrieb infolge Verlustes an Treibkraft nicht rationell erschien.
EMI1.3
auf die einfachste Weise dadurch erreicht, dass der Antrieb des Unterstempels durch ein Exzenter erfolgt, das von dem auf den Oberstempe) einwirkenden liebet mittelst eines Lenkers und eines Hebelarmes betätigt wird.
In der Zeichnung ist ein schematisches Ausführungsbeispiel der Erfindung dargestellt, u./w. zeigt die Fig. 1 einen Längenschnitt der Presse und Fig. 2 einen wagrechten Schnitt durch das Exzenter.
EMI1.4
mittelst des Bolzens. 9 und der Arme. M das Exzenter 12 betätigt, an welchem der Unter- stempel 11 drehbar gelagert ist (Fig. 2).
Diese Exzenterwelle ist unter dem Unterstempel angeordnet, so dass das Exzenter direkt auf den Stempel einwirkt. Dabei muss das Exzenter so gestellt sein. dass die lie- @ wegungen der Stempel möglichst gleichartig sind. Wird der Hebel 3 mit einem Drucke,
EMI1.5
**WARNUNG** Ende DESC Feld kannt Anfang CLMS uberlappen**.
<Desc / Clms Page number 1>
Mold block press with press rams that can move against each other at the same time.
The previously common machines for pressing rubble and. the like were carried out in various forms, among which are noteworthy those machines
EMI1.1
Press stamping takes place. This double-sided pressing has been accomplished using hydraulic pressure or other suitable mechanical means. The devices had the disadvantage, however, that the pressure on both sides could never be completely simultaneous, because it was necessary that the pressure from top to bottom and consequently the resistance on the part of the compressed mass reached a certain amount.
EMI1.2
will.
In order to counteract these inconveniences, devices have been proposed by means of which a simultaneous double-sided printing is achieved, but these have the disadvantage that the construction of the press was cumbersome and expensive and the operation did not appear to be efficient due to the loss of driving force.
EMI1.3
achieved in the simplest way in that the lower ram is driven by an eccentric which is actuated by the operator acting on the upper ram by means of a link and a lever arm.
In the drawing, a schematic embodiment of the invention is shown, u./w. Fig. 1 shows a longitudinal section of the press and Fig. 2 shows a horizontal section through the eccentric.
EMI1.4
by means of the bolt. 9 and the poor. M actuates the eccentric 12 on which the lower punch 11 is rotatably mounted (FIG. 2).
This eccentric shaft is arranged under the lower punch so that the eccentric acts directly on the punch. The eccentric must be set this way. that the movements of the stamps are as similar as possible. If the lever 3 is pressed with a
EMI1.5
** WARNING ** End of DESC field may overlap beginning of CLMS **.