<Desc/Clms Page number 1>
Österreichische PATENTSCHRIFT Nru 16593.
FIRMA JOSEF HELLER IN MÜNCHEN. Stuhl mit durch Umwenden beiderseitig benützbarem Sitz.
EMI1.1
Stuhl, bei welchem sowohl das Wenden des Sitzes als auch die Auslösung des den Sitz feststellenden Stcllstiftes durch einen gemeinsamen Hebel erfolge kann.
In der Zeichnung ist ein solcher Stuhl in Fig. 1 schaubildlich dargestellt, während Fig. 2 die Sitzfläche mit Mechanismus von oben gesehen und Fig. 3 den letzteren in einem Höhenschnitt zeigt.
Wie hieraus ersichtlich, erfolgt die Betätigung der mit ihrer Achse a in der Mitte drehbar gelagerten Sitzfläche b durch einen seitlich am Stuhl angebrachten Handhebel c, der mittels seines Zahnsegmentes d in ein Zahnrad e eingreift, dessen Lagerachse durch einen Ketten- oder Schnurantrieb f mit der Achse (, a in Verbindung steht.
EMI1.2
seinem einem Hebelarm mit dem unter Federdruck stehenden Stellstift h in Verbindung, während sich das andere Ende desselben mit seinem Gleitstück i gegen den nach unten verringerten Handhebel c anlegt.
Der Stellstift h, der durch eine Abschrägung r an der Stirnkante des Sitzes b, bei dessen Drehung in die Gebrauchslage zuerst zurückgedrückt wird, schnappt nach vollzogener Drehung selbsttätig in eine entsprechende Rast des Sitzes ein, denselben dadurch fixierend. Das Auslösen des Stellstiftes kann unter Vermeidung eines eigenen Handhelbels gleichfalls durch den zum Wenden der Sitzfläche dienenden Handhebel c erfolgen, indem derselbe mittels eines Stiftes m derart beweglich mit seiner das Zahnsegment tragenden Achse verbunden ist, dass er in der in Fig. 3 angegebenen Pfeil- ri-ltung bewegt werden kann.
Dadurch wird das untere Ende des Handhebels c auf das Gleitstück i des Doppelhebels g einen Druck ausüben, demzufolge derselbe den Stellstift A aus der Rast des Sitzes zurückzieht und letzteren dadurch freigibt. Durch eine darauffolgende Teildrehung des Handhebels c wird dann der Sitz selbst in der angegebenen Weise gedreht und nach erfolgter Drehung mit Hilfe der auch auf der anderen Seite des Sitzes vorgesehenen Rast neuerdings fixiert.
Zum jedesmaligen Wenden des Sitzes ist also stets zuerst ein seitliches Herausdrehen des Handhebels c und eine darauffolgende Teildrehung desselben nach der einen oder anderen Richtung erforderlich.
**WARNUNG** Ende DESC Feld kannt Anfang CLMS uberlappen**.
<Desc / Clms Page number 1>
Austrian PATENT Letters No. 16593.
JOSEF HELLER COMPANY IN MUNICH. Chair with seat that can be used on both sides by turning it over.
EMI1.1
Chair in which both the turning of the seat and the release of the adjusting pin locking the seat can be carried out by a common lever.
In the drawing, such a chair is shown diagrammatically in FIG. 1, while FIG. 2 shows the seat with the mechanism from above and FIG. 3 shows the latter in a vertical section.
As can be seen from this, the actuation of the seat b, which is rotatably mounted with its axis a in the middle, is carried out by a hand lever c attached to the side of the chair, which engages by means of its toothed segment d in a gear wheel e, whose bearing axis is connected to the by a chain or cord drive f Axis (, a is connected.
EMI1.2
its one lever arm with the spring pressure adjusting pin h in connection, while the other end of the same with its slider i rests against the downwardly reduced hand lever c.
The adjusting pin h, which is pushed back by a bevel r on the front edge of the seat b, when it is rotated into the position of use, automatically snaps into a corresponding detent of the seat after the rotation has been completed, thereby fixing it. The actuating pin can also be triggered by the hand lever c, which is used to turn the seat surface, avoiding its own hand lever, in that the same is movably connected to its axis carrying the toothed segment by means of a pin m that it is in the arrow indicated in FIG. direction can be moved.
As a result, the lower end of the hand lever c will exert a pressure on the slider i of the double lever g, as a result of which the latter withdraws the adjusting pin A from the detent of the seat and thereby releases the latter. The seat itself is then rotated in the specified manner by a subsequent partial rotation of the hand lever c and, after the rotation has taken place, is now fixed with the aid of the detent provided on the other side of the seat.
For each time the seat is turned, it is always necessary to first unscrew the hand lever c laterally and then partially rotate it in one direction or the other.
** WARNING ** End of DESC field may overlap beginning of CLMS **.