1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
|
# Sample configuration file for smartd. See man smartd.conf.
# Home page is: http://smartmontools.sourceforge.net
# $Id: smartd.conf,v 1.33 2004/01/13 16:53:06 ballen4705 Exp $
# smartd will re-read the configuration file if it receives a HUP
# signal
# The file gives a list of devices to monitor using smartd, with one
# device per line. Text after a hash (#) is ignored, and you may use
# spaces and tabs for white space. You may use '\' to continue lines.
# You can usually identify which hard disks are on your system by
# looking in /proc/ide and in /proc/scsi.
# The word DEVICESCAN will cause any remaining lines in this
# configuration file to be ignored: it tells smartd to scan for all
# ATA and SCSI devices. DEVICESCAN may be followed by any of the
# Directives listed below, which will be applied to all devices that
# are found. Most users should comment out DEVICESCAN and explicitly
# list the devices that they wish to monitor.
DEVICESCAN
# First (primary) ATA/IDE hard disk. Monitor all attributes, enable
# automatic online data collection, automatic Attribute autosave, and
# do a short self-test every day at 2am, and a long self test
# Saturdays at 3am.
#/dev/hda -a -o on -S on -s (S/../.././02|L/../../6/03)
# Monitor SMART status, ATA Error Log, Self-test log, and track
# changes in all attributes except for attribute 194
#/dev/hdb -H -l error -l selftest -t -I 194
# A very silent check. Only report SMART health status if it fails
# But send an email in this case
#/dev/hdc -H -m admin@example.com
# First two SCSI disks. This will monitor everything that smartd can
# monitor. Do extended self-tests Wednesdays at 6pm and Sundays at 1 am
#/dev/sda -d scsi -s L/../../3/18
#/dev/sdb -d scsi -s L/../../7/01
# Monitor 4 ATA disks connected to a 3ware controller card which uses
# the 3w-xxxx driver. Do a long self-tests Sundays at 1, 2, 3, and 4 am
#/dev/sdc -d 3ware,0 -a -s L/../../7/01
#/dev/sdc -d 3ware,1 -a -s L/../../7/02
#/dev/sdc -d 3ware,2 -a -s L/../../7/03
#/dev/sdc -d 3ware,3 -a -s L/../../7/04
# HERE IS A LIST OF DIRECTIVES FOR THIS CONFIGURATION FILE
# -d TYPE Set the device type: ata, scsi, removable, 3ware,N
# -T TYPE set the tolerance to one of: normal, permissive
# -o VAL Enable/disable automatic offline tests (on/off)
# -S VAL Enable/disable attribute autosave (on/off)
# -n MODE No check. MODE is one of: never, sleep, standby, idle
# -H Monitor SMART Health Status, report if failed
# -l TYPE Monitor SMART log. Type is one of: error, selftest
# -f Monitor for failure of any 'Usage' Attributes
# -m ADD Send warning email to ADD for -H, -l error, -l selftest, and -f
# -M TYPE Modify email warning behavior (see man page)
# -s REGE Do self-test when type/date matches regular expression (see man page)
# -p Report changes in 'Prefailure' Normalized Attributes
# -u Report changes in 'Usage' Normalized Attributes
# -t Equivalent to -p and -u Directives
# -r ID Also report Raw values of Attribute ID with -p, -u or -t
# -R ID Track changes in Attribute ID Raw value with -p, -u or -t
# -i ID Ignore Attribute ID for -f Directive
# -I ID Ignore Attribute ID for -p, -u or -t Directive
# -v N,ST Modifies labeling of Attribute N (see man page)
# -a Default: equivalent to -H -f -t -l error -l selftest
# -F TYPE Use firmware bug workaround. Type is one of: none, samsung
# -P TYPE Drive-specific presets: use, ignore, show, showall
# # Comment: text after a hash sign is ignored
# \ Line continuation character
# Attribute ID is a decimal integer 1 <= ID <= 255
# All but -d, -m and -M Directives are only implemented for ATA devices
#
# If the test string DEVICESCAN is the first uncommented text
# then smartd will scan for devices /dev/hd[a-l] and /dev/sd[a-z]
# DEVICESCAN may be followed by any desired Directives.
|