oreka-user Mailing List for oreka

Hi! I'm programming now orkaudio/sounddevice module, which is broken 
after change of the plugin interface. And I wanted to release a patch or 
a newer version of the oreka GPL. However, I found that SVN of Oreka is 
unregistered by webmaster because of zero activity. And there is no 
hints on the cite about a code exchange.

So that was my question: how to publish my code of oreka to make it 
visible to other users?

Hello,

I am having problems with call recording. they do not seem to be recording any calls since august. i have gone through the checklist and also updated wincap, restarteed the services but no success. it has been recording for two years but can not find solution to this. i do not know what the problem is and can not find any forums for support.


Naser Ahmed
IT department
Tel: 02074261264
E-mail: n....@ei...

Hello all,



Has anybody managed to successfully setup Oreka for call recording from
Cisco CallManager (6.X and above) It uses Built-In-Bridge functionality of
the phone where the recording is initiated with SIP towards the recorder. I
see SIP INVITE sent to Oreka server (with Wireshark), but the server is
sending ICMP 590 Destination unreachable(port unreachable). I think CUCM
side is fine. There has to be some additional setup for Oreka to send CUCM
back 200 OK or sth so that RTP can start (I tried Oreka with span port on
phone  and it creates records). I assume I would have to set somewhere Jtapi
username which I created on CallManager. Any ideas?

Thanks a lot for any suggestions, I am pretty new at Oreka software so still
struggling...



regards


goran

I'm trying to install OrkAudio, OrkWeb and OrkTrack on a CentOS 5.6 or 5.7 32bit system using the installation scripts. When I attempt to install I get an error that tells me that it can't find YUM. I've used YUM to install other applications so I know it is installed and working properly from that stand point. I've also used the installation scripts in the past to install this on CentOS 5.6 so I'm not sure what has changed between the last time I successfully installed and the last couple of attempts.

Any ideas as to why the installation script is failing to locate YUM to complete the install process?

Keith D. Garris
Service Desk Analyst
Catapult Technology Ltd.

7500 Old Georgetown Road
11th Floor
Bethesda, MD 20814

Office (717) 217-1251
Cell (240) 994-8719
kei...@ca...<mailto:kei...@ca...>
www.catapulttechnology.com<http://www.catapulttechnology.com/>

Leveraging People, Processes, and Technology. A Service-Disabled Veteran-Owned Business.


________________________________
This e-mail, including attachments, may include confidential and/or proprietary information, and may be used only by the person or entity to which it is addressed. If the reader of this e-mail is not the intended recipient or his or her authorized agent, the reader is hereby notified that any dissemination, distribution, or copying of this e-mail is prohibited. If you have received this e-mail in error, please notify the sender by replying to this message and delete this e-mail immediately.

Orkeka is working great.  It records and plays perfectly.  However, the
service "Orkaudio" randomly stops for no apparent reason.  I can manually
start it, and it continues working fine.

I have temporarily create a batch file "net start orkaudio" that runs every
so often to start it if it stops.

Has anyone else seen this problem?  Any ideas?

Windows 2003 server.

Orkeka is working great.  It records and plays perfectly.  However, the
service "Orkaudio" randomly stops for no apparent reason.  I can manually
start it, and it continues working fine.

I have temporarily create a batch file "net start orkaudio" that runs every
so often to start it if it stops.

Has anyone else seen this problem?  Any ideas?

Windows 2003 server.

EDIT:  Actually, this is Windows XP 64-Bit, not 2003.  Also, it seems to be
about a 1-week interval that it works for before it stops.  There is nothing
in the logs to indicate a stop reason.  It shows recording all the way to
where it stops, and then nothing until start.

Any ideas would be appreciated.

Can AGC be enabled in config.xml? I'm trying to record radio traffic and get "AGC disabled in config.xml" in log file. Recordings start but never complete.

Thanks,
Brad Martin
Information Technology
Black Hills Corporation
P - 605-721-2189
C - 605-431-2782


________________________________

This electronic message transmission contains information from Black Hills Corporation, its affiliate or subsidiary, which may be confidential or privileged. The information is intended to be for the use of the individual or entity named above. If you are not the intended recipient, be aware the disclosure, copying, distribution or use of the contents of this information is prohibited. If you received this electronic transmission in error, please reply to sender immediately; then delete this message without copying it or further reading.

Can AGC be enabled in config.xml? I'm trying to record radio traffic and get "AGC disabled in config.xml" in log file.

Thanks,
Brad Martin
Information Technology
Black Hills Corporation
P - 605-721-2189
C - 605-431-2782


________________________________

This electronic message transmission contains information from Black Hills Corporation, its affiliate or subsidiary, which may be confidential or privileged. The information is intended to be for the use of the individual or entity named above. If you are not the intended recipient, be aware the disclosure, copying, distribution or use of the contents of this information is prohibited. If you received this electronic transmission in error, please reply to sender immediately; then delete this message without copying it or further reading.