Open Source Serial Software - Page 7

SerServ is a TCP/IP server that allows multiple clients to use a serial port on the host machine over the network.

This is a serial-to-ethernet and/or ethernet-to-serial gateway project. Such a software could reveal useful in many cases.

Secom is an object-oriented library of portable, reusable components for communicating over serial devices. With secom you can develop an application that will compile and execute on Posix and Windows, with little to no changes to the source code.

ttypatch is a Linux application that permits two or more "serial port user programs" to reliably connect to each other without the use of actual serial ports. Also acts as a virtual patch panel among any number of real and virtual serial ports.

Serial Debugger, moninter and control the behavior of the serial ports.

A Perl program to write characters (eg. a lot number) to an alphanumeric display via rs232. Includes Java Swing GUI. Developed for production in pharma industry. Currently two lines included. German version.

This project is dll which can help user to communicate with serial port.

Simple Serial COM read/write program. I needed it for Caller ID read modem driver so it has command auto complete for AT commands. It is a good replacement for HyperTerminal. Made for .NET Framework 2.0

Serial port communication. An usable sample. * support remote control mode (with two fish encryption)

PROJECT MOVED TO: https://github.com/damogranlabs/serial-tool See releases page: https://github.com/damogranlabs/serial-tool/releases Serial Tool is a utility for developing serial communications, custom protocols or device testing. You can set up bytes to send accordingly to your protocol and save configuration to a file – which can be used another time. You can send multiple byte arrays, you can send sequence of different byte arrays and put delay between them. You can read data in HEX or ASCII. You can even write a note to yourself like: “CH1: toggle LED 1”.

This project is an enhanced version of ser2net, a proxy that allows telnet/tcp connections to be made to serial ports on a machine.

This application is a ASCII-based data scope. When used with a 'spy' cable such as the CBL-Full-1A product from www.commfront.com this progrmam shows the ASCII chars on both sides of a comm link. There are three main tabs on the user interface. The 'Vertical' tab displays the comm link conversation in a vertically-scrolling half-duplex mode. Each 'side' of the conversation is detected by the user-configured 'start msg' and 'end msg' byte sequence. The 'Horizontal' tab shows bytes, one at a time, as they are received on each side of the link so the relative timing relationships can be monitored. Printable ASCII chars are shown. Non-printable are shown with a '0x' prefix. The two sides of this link referred to as 'Port 1' and 'Port 2'. Each side must communicate at the same baud rate. Each side can have its' own start message and end message character configurations. A log tab where state and error messages can be reviewed.

Shooting Chrony Data Downloader, a program that allows downloading of data acquired by the device

System tray caller id applet for Windows based on .NET framework. Turns on caller ID function of the modem, and when any output occurs (a call comes in), a small log window appears showing all text, verbatim.

A dialect-neutral Smalltalk library which supports communication with NMEA enabled devices, such as GPS receivers. The initial specific target device will be a Magellan GPS315 receiver.

SoftDash PC allows realtime control of the Connect2Car MFC controller unit installed in a vehicle. Softdash PC can communicate with the MFC hardware either via a serial connection or a Bluetooth Connection. This project allows for open ended expansion.

This application will be the software part for "Universal Atmel Flash 8051 / AVR Programmer" that can be found at : http://home.tiscali.de/peterd/tools/proflash/index.htm (on my opinion this is the best free MCS51/AVR programmer).

Windows program to control your Sony DVP-CX777ES 400-disc DVD player via its RS232 port connected to the serial port of your computer. Includes documentation and all source.

HW(VHDL) and SW of logic analyzer and On-Chip-Verification(OCV) for Value Change Dump(VCD) file format that exported to seemd SystemC ,ModelSIM, and many other EDA tools. Very easy and Simple.

TJTerm is an open source serial port terminal program written in Java, running on Linux, Mac OS and Windows. It supports color, logging, macros, graphical hex and/or ASCII input and output and more.

Room temperature monitoring system.

A server application, a TELNET server, which mainly works as an interface for users to connect to the server serial port or another TELNET server. Any new ideas may be added in along the implementation.

This library, then DLL, designed for use with weighing terminal CI-5010A on the RS-422/485 or RS-232 via a physical or virtual COM port over USB in OS NT/2000/2003/XP/Vista/7/8 and reads and decodes the data of the operation, gross weight, net weight, unit number, value and sign weight, units and features indicators. Restoring communications using virtual serial port automatically. ORDER use and limitations: 1. You can optionally set the COM port in the procedure 'reinit()' with constantly raised the flag of activation in the library is being processed. 2. Parameter gl_count procedure 'getdata' indicates the number of received packets of COM-port. 3. Implemented AutoTrack pulling converter RS-485/USB (via SetupAPI) and reconnect to the specified port initialization.

Simple and dumb tool to access serial ports. Mainly intended for use to access serial consoles of various hardware.

The Transparent Print utility program for Linux.