B e s c h r e i b u n E
zur Gebrauehsmusteranmeldung ! Einkochglasöffner an Flaschenbürsten,
nebst einem Schutz anspruch.
Verwendungszweck :
Sollen zugekochte Einkochgläner gebf fnet wordens mit der Rand,
entstehen folgende Schwierigkeiten : Der kurze, hervorstehende
vorsprung (sogenannte Zunge) des Gummiringes kann mit 2 Fingern
schlecht gefasst werden. Durch dasunzweekmässige ziehen daran
wird die Zunge leicht abgerissen. Bei abgerissener Zunge muss
zum
öffnen zwischen Glas und Deckel ein harter Gegenstand gedrückt
werden, wodurch das Glas bzw. der Deckel beschädigt und unbrauchbar
wird, weiter wird auch der Inhalt durch hereinfallen von kleinen
Glasscheiben ungeniessbar.
Um diesen Uebelstand abzuhelfen, habe ich eine Flaschenbürste
hergentellts dessen Griff so kunstruiert ist, das jedes Einkoch-
glas zuverlässig geöffnet werden kann, ohne das oben besehr.
Nachteile enstehen. Der Einkoehglasoffner besteht aus einer
normalen Flaschenbürste. Der Stiel ist aus Draht gedreht dass
sich an seinem Ende eine größere Oese bildet, die Oese verläuft
in zwei parallel laufenden, und dicht aneinander liegenden
und
federnden Drahtenden weiter, bis an einer 2. kleineren Oese.
Dieses Ganze bildet den Einkochglasoffner an der Flaschenbürste,
der Einkochglasöffner verläuft dann spiralförmig bis zur Aufnahme
der Borsten.
Beim Gebrauch des Rinkochglasoffners wird die Zunge des Gummi-
ringes in die grosse Oese eingeführt, mit der anderen Hand
wird
die Zunge festgehalten und schiebt dieselbe zwischen den parallel
laufenden, federnden Drahtteil, bis zur Mitte der beiden Oesen,
durch die Federung wird die Zunge festgehalten. An der grossen
Oese wird jetzt der Einkochglasoffner nach oben zum Deckel
gedreht, hierdurch wird der Gummiring gespannt und das Glas
ist
müh elo2 n et
Description
for registration of usage samples! Jar opener on bottle brushes,
in addition to a claim for protection.
Purpose of use :
Should cooked jars be opened with the edge,
the following difficulties arise: The short, protruding one
projection (so-called tongue) of the rubber ring can be done with 2 fingers
to be badly caught. By pulling on it for no purpose
the tongue is torn off easily. If the tongue is torn off, the
open a hard object pressed between the glass and the lid
become, whereby the glass or the lid is damaged and unusable
The content will continue to fall through small ones
Glass panes inedible.
To remedy this problem, I have a bottle brush
hergentellts whose handle is so crafted that every
glass can be opened reliably without the above.
There are disadvantages. The Einkoehglasopener consists of one
normal bottle brush. The stem is twisted from wire that
a larger eyelet forms at its end, which runs through the eyelet
in two parallel and close to each other and
springy wire ends up to a 2nd smaller eyelet.
This whole forms the jar opener on the bottle brush,
the jar opener then runs in a spiral to the receptacle
the bristles.
When using the Rinkochglasopener the tongue of the rubber
ring is inserted into the large eyelet with the other hand
held the tongue and pushes it between the parallel
running, springy wire part, up to the middle of the two eyelets,
the tongue is held in place by the suspension. At the big one
The eye of the jar opener now becomes the lid at the top
rotated, this will tighten the rubber ring and the glass is
müh elo2 n et