Open Source C Wireless Software

AutoAP is a script that continuously scans for open Wi-Fi connections, tests them for validity, and connects to the strongest signal. If the connection is lost, the script scans again and finds the strongest valid signal again, and maintains a continuous connection to the internet in a mobile or portable environment. The script paremeters are highly configurable, including ability to configure secure connections. AutoAP is an add on to DD-WRT that allows routers to continuously scan for and connect to open (and predefined WEP) wireless networks. Ultimately the goal is to develop an easily deployable firmware that facilitates fast and easy mesh network creation. Typically, you would use this script on your router while in Repeater Mode, Client Mode, or Client-Bridged Mode.

Comgt is a command line tool for controlling, configuring and interacting with Option Wireless 3G and 2G ( HSDPA, UMTS, EDGE, GPRS, GSM) data devices within the Linux environment.

Scan for WiFi devices, block selected connections, create dozens of networks and confuse WiFi scanners! Version 3 is in development. It is stable to use, but it is very different. It is command-line based, which allows it to offer not just more features, but make them more customizable. This software allows you to easily perform a variety of actions to test 802.11 wireless networks by using an inexpensive ESP8266 WiFi SoC (System On A Chip). The main feature, the deauthentication attack, is used to disconnect devices from their WiFi network. No one seems to care about this huge vulnerability in the official 802.11 WiFi standard, so I took action and enabled everyone who has less than 10 USD to spare to recreate this project. I hope it raises more attention on the issue. In 2009 the WiFi Alliance actually fixed the problem (see 802.11w), but only a few companies implemented it into their devices and software.

Remote control software for applications using wi-fi or bluetooth.

Wepdecrypt is a Wireless LAN Tool written in c which guesses WEP Keys based on a active dictionary attack, key generator, distributed network attack and some other methods, it's based on wepattack and GPL licensed

Tomato USB is a fork of popular Tomato firmware (http://www.polarcloud.com/tomato) for Broadcom-based routers. This fork adds built-in support for USB port, wireless-N mode support, support for several newer router models, and various enhancements.

IEEE 802.15.4 networkong stack covers PHY and MAC layers (PHY layer implemented in hardware and MAC optionally implemented in software). Also 6lowpan (IPv6 packet encapsulation) is implemented for use by IEEE 802.15.4 and BT LE networks. Note: due to licensing restrictions (and despite project's name) we do not plan to implement any ZigBee related stack parts.

wavemon is a wireless device monitoring application that allows you to watch signal and noise levels, packet statistics, device configuration and network parameters of your wireless network hardware. It should work (though with varying features) with all devices supported by the Linux kernel. Apart from debian/ubuntu packages and slackbuild scripts for wavemon, this repository contains the full source code.

The WiFi Guard Dog project is a complete and embeddable captive portal solution for wireless community groups or individuals who wish to open free HotSpots while preventing abuse of their connection. Go to dev.wifidog.org to download the latest version.

GKrellm plugin monitoring Linux BlueZ adapters

Add 3.5G USB dongle support on ASUS RT-N13U The RT-N13U UI is good enough, so I don't change much. Only add 3.5G setting in advance setting--> USB Application This FW supports HUAWEI E169 E220, Bandluxe C270, OPTION 225 now.

A new/clean Linux kernel driver/module for IEEE 802.11 Wireless Ethernet Adapters based on Realtek's RTL8180L and RTL8185L chipset

Airpwn is a tool for generic packet injection on an 802.11 network.

OpenDMTP is a protocol/framework that allows communications with small devices (mobile phones, PDA's, and other high-latency/low-bandwidth devices), especially geared towards the transmission of GPS, temperature, and other remote monitoring information.

nwGTPv2 is free and open source implementation of GPRS Tunneling Protocol version 2 (GTPv2) or Evolved GTP (eGTP). GTPv2 is primarily used for control signalling between Serving Gateway SGW and PDN Gateway (PGW) in Evolved Packet Core (EPC).

PepperSpot is a captive portal or wireless LAN access point controller which support the IPv6 protocol. It supports web based login and it supports Wireless Protected Access (WPA). Authentication is handled by your favorite radius server (over IPv4/IPv6)

pwntooth is designed to automate Bluetooth Pen-Testing. It scans for devices, then runs the tools specified in the pwntooth.conf; included blueper, bluesnarfer, Bluetooth Stack Smasher (BSS), carwhisperer, psm_scan, rfcomm_scan, and vcardblaster.

Zulu is a light weight 802.11 wireless frame generation tool to enable fast and easy debugging and probing of 802.11 networks. It has an intuitive command line interface and operates with the madwifi-ng network drivers.

Cloud hub is a link-level wireless mesh networking implementation. With cloud hub firmware, access points automatically find each other, optimize connection topology, and allow other ad-hoc wireless users to join as clients.

Router Radio Protocol Tools provide router (server) simulator and a radio (client) simulator for the radio-router protocol. The router simulator can be used to support the integration of the protocol into a radio.

TeenyLime is a middleware simplifying the development of wireless sensor networks applications. The foundation for TeenyLime is the notion of tuple space, a repository of elementary sequences of typed fields, called tuples.

ULLA allows developers of network aware applications to access data from device drivers similar to the Wireless Extensions on Linux. However, its new design simplifies the API syntax and expands the access to all wireless technologies such as GSM, BT.

Synchronize bluetooth mobile phone with thunderbird, lightning, sunbird, outlook etc.

OS independent implementation of the Trusted Network Connect (TNC) specification from Trusted Computing Group (TCG). Functions for loading and communicating with TNC plugins, sample IMC and IMV plugins, TNCCS-XML support on Windows, Linux, Mac, *BSD

vtrunkd - network link bonding and multichannel VPN. Vtrunkd is a Linux VPN daemon used to combine several connection paths into one aggregated channel. Features latency, reordering and jitter management, behaviour analysis optimizations for encapsulated protocols, bufferbloat control, packet redundancy, and multiple cpu cores utilization. Up to 30 heterogenous links bonding supported. Used for live streaming, LTE/3G/Wi-Fi link bonding. 32/64-bit, x86, MIPS and ARM supported. Supports python plug-ins for new algorithms implementation. Open source version developed and commercial support provided by Vrayo Systems, http://vrayo.com. No encryption supported yet.